Korg PS-3300 - Caution; Power Supply Caution; Caution when setting up a patch.; Impedance of inputs and outputs used for modulation.

DDL
LAPP
AP
LLL
ST ON
4 SRFOFS
4-1 @RI2DUT
ACORMBIE RA SLA BIB ENS AE
D8 HAFAN (PSU-3302) MOEA 2A
CULT
L,
FMOMKHD
HS
EMRIE
7
CUMEEORW TS ST,
Yay TMT SE. BAER
OME
DEPOT,
QP
iM
IEMIET
afer
¢
1B.
tig. 57 Power supply voltage sel
(MHMELL 7 9-LFUSERNI—)
and
tuse
holder
ee
4 Caution
41 Power Supply Caution
If it is ever necessary to change the power
supply voltage of this unit, you can do so
by
using
the
power
supply
voltage
selector
under the signal mixer panel. (Unscrew the
two screws at the top of the PSU-3302).
If you use the wrong power supply voltage,
it will cause malfunctioning. If you use the
synthesizer in another country, check the
line voltage and change the voltage selector
setting if necessary.
UL
1b
4-2 WwF-9-DLWT
RAULOBESADMFICMIFBUTCESL.
AM EDGANME NZS OE ORM EA
MIVTH OSTA He CL 22a RET AL
Tertte< 2. ERO ERT S25
sour lst.
SCOMAMBSS CABIN YRKeIVRO—ILL
KDEFSBSI.
ANTLYE-IVAH10kKQ
REO: hECER<ESU.
| BRBALIOTVE—-IVA
42 Caution when setting up a patch.
Never connect a control voltage signal to
an input jack if the control voltage is high-
er than the rating displayed on the jack
Every jack has built-in protection circuits,
but to keep the synthesizer operating nor-
mally, please obey the above rule.
If you connect a control voltage signal
from this unit to an input on another unit,
make sure the input impedance of the
other unit is higher than 10kohm.,
a eae ee ae
Impedance
of
inputs
and
outputs
used
for
modulation.
| Output impedance:
WAtreE-FLA
10K@ &F less than Ikohm.
|
Input
impedance
—
Analog
inputs:
7+07A%
10k2
iF
more
than
10kohm.
Digital
inputs:
#29
VAD
1KQ
tLF
less
than
1
kohm.
4-3 60PIRII—I2DWT
6
OP
yT7izlé
KORG
PS}'I-—ZADPIR
PU
DEER
LBUITCESU.
GOPMRI— KF LMMTSE DI, BAK, A
Mase bt, MME Wo TH CHL T
xREOFIVYD
B-. REME Mh te £5 TeHBARD TD 6 GE
EV 7a eo EY FERIRLES
.
MMM
OF
=o
FeTEoT
KIS
MG-1,
MG-2,GEG,
VP,
S/H%
©
OMODULA:
+ RE GIS aL. RO RIE
ELTF zr FLT (HS.
43 6O0P Connector caution
Do not use the 60P jack for connections
with
anything
except
PS-series
units
and
accessories. Feel free to contact our techni-
cal staff about the use of these connections.
Always turn off the power of both units
before making a 60P connection or unplug:
ging a 60P plug.
®
Trouble
shooting
If
you
think
something
is
not
working
right,
return
all
controls
(and
patch
cords)
to
the
normal
setting.
Then
check
the
modules
one
at a time
for
the
source
of the
trouble.
To
testy
operation
of
modulation
signal
generators
and
processors
such
as
the
MG-1,
MG-2,
GEG,
VP,
and
S/H,
connect
them
to
the
SG
section
and
check
the
pitch
changes
produced.
SS Se eS See aS eS ee Ee ee