What to do if Kowa AP-7000 Medical Equipment says 'Darken the room'?
If your Kowa Medical Equipment displays 'Darken the room', it means the room is too bright for the instrument to properly set the luminance in the dome. You should darken the room and then press the [OK] button.
What to do if Kowa Medical Equipment shows 'Cannot set the stimulus intensity'?
If your Kowa Medical Equipment displays 'Cannot set the stimulus intensity', first check if a head band is obstructing the sensor in the dome. If so, remove the head band and restart the instrument. If there's no obstruction, the projection lamp intensity might be reduced. If the lamp is lit, consider replacing it soon. If the projection lamp is off, replace it immediately with a new one. If the message persists after replacing the lamp, contact Kowa or your Kowa dealer.
What to do if Kowa Medical Equipment displays 'Cannot set the background intensity'?
If your Kowa Medical Equipment displays 'Cannot set the background intensity', first ensure that a head band isn't obstructing the sensor inside the dome. Remove it and restart the instrument if necessary. If there's no obstruction, the background lamp's intensity may be reduced. If the lamp is lit, consider replacing it soon. If the background lamp is off, contact Kowa or your Kowa dealer.
What to do if Kowa AP-7000 shows 'No Database file'?
If your Kowa Medical Equipment displays 'No Database file', ensure that the network components (LAN cable, hubs, etc.) are properly connected and working to establish a healthy network. Also, verify that the data save destination (personal computer, hard disk drive, USB flash drive, etc.) is correctly connected and operating. Correct any connection or operational issues and then select [Search again]. If unsure, select [Cancel], check the network environment and data save destination, and then restart the instrument. If the issue persists, contact Kowa or your Kowa dealer.
What to do if Kowa AP-7000 Medical Equipment displays 'Cannot initialize the motor'?
If your Kowa Medical Equipment displays 'Cannot initialize the motor', turn off the power and then restart the instrument. If the same message appears again, contact Kowa or your Kowa dealer.
What to do if Kowa AP-7000 shows 'Cannot run camera viewer'?
If your Kowa Medical Equipment displays 'Cannot run camera viewer', it indicates an error with the eye fixation monitoring camera. Try restarting the instrument. If the same message appears after the restart, contact Kowa or your Kowa dealer.
What to do if Kowa Medical Equipment displays 'Failed to acquire the pupil position'?
If your Kowa Medical Equipment displays 'Failed to acquire the pupil position', it means there is a failure in the gaze monitor setting. To retry the acquisition, confirm the eye fixation, and then press [OK]. To not retry, press [Cancel]. If you press [Cancel], the gaze monitor function will be deactivated for this examination.
What to do if Kowa AP-7000 displays 'The examined eye is incompatible with the fundus image'?
If your Kowa Medical Equipment displays 'The examined eye is incompatible with the fundus image', it means that during the perimetry coordinate setting on a fundus image for fundus perimetry, the positions of the fovea and optic disc have been reversed in comparison to the actual examined eye. Verify that the examined eye matches the fundus image, and also check whether the examined eye is left or right.
What does it mean when Kowa AP-7000 says 'Database repair will begin'?
If your Kowa Medical Equipment displays 'Database repair will begin', it means the database check and rebuilding are automatically being executed. Please wait for a while.
What to do if Kowa AP-7000 displays 'Cannot back up'?
If your Kowa Medical Equipment displays 'Cannot back up', check the current data save destination and data content. If there are no problems with these, try changing the backup media or backup destination.
General| Category | Medical Equipment |
|---|---|
| Type | Automated Perimeter |
| Brand | Kowa |
| Model | AP-7000 |
| Stimulus Size | Goldmann I-V |
| Power Supply | AC 100-240V, 50/60Hz |
| Examination Modes | Static, Kinetic |
| Background Illumination | 31.5 apostilbs |
| Stimulus Duration | 200 ms |
| Display | Color LCD |
| Data Storage | Internal memory, USB |
| Printer | External |
To Next Page
