通讯口确认
(Communication Ports)
AC100 - 240 V
50/60 Hz
EA-AC
2). AC接入(AC Wiring)
GND
开箱确认
(Unpack and Inspect)
1
3
4
6
8
PC
与
EA7E
的连接
(Connect Touch Panel to PC)
安全情报
如何设定时间 (The time set of a clock)
Quick Start Guide
･电缆要求：单芯线
0.2
～
2.5mm²
多股线
0.2
～
2.5mm²
、
AWG24
～
12
･接线端子紧固扭矩
:
0.5
～
0.6Nm
･电缆要求：单芯线0.2 ～ 2.0mm²、多股线0.2 ～ 2.0mm²、AWG24 ～ 14
･端子紧固扭矩 : 0.5Nm
･本体安装紧固扭矩： 0.35Nm
・
Wire range: Solid: 0.2-2.0mm², Stranded: 0.2-2.0mm², AWG24-14
・
Screw Torque(terminal) : Connecting Screw: 0.5Nm, Screw for flange: 0.5Nm
・
Screw Torque(mounting bracket) : 0.35Nm
Use DC24V or AC for power source. EA-AC (Option) is required for AC power.
1. Connect a DC24V power supply (4.3″Model: DC12~24V) as shown in figure 1). DC wiring.
2. Connect EA-AC as shown in figure 2). AC wiring.（Except 4.3″Model）
Please make sure that all insertions shown in the picture are
included in the carton.If any item is missing or damaged,
please contact the store you purchased.
(Safety Information)
Connect the Touch Panel to PC as shown.
如图所示方法来连接触摸屏和 PC。
To access the MAIN MENU of the Touch panel setup screens,
press the upper left corner of the panel display area for 3 seconds
as shown to the left.
按住触摸屏左上角3秒，进入系统设置画面的主菜单画面。
按“System Setup”键
Press “Clock Setup”
按“Clock Setup”键
Adjust the internal clock
调整触摸屏内部时钟
・
Do not use the Touch Panel to make switches that are related to safety of people or major damages
(emergency safety switches, etc).
・
Be sure that class D grounding is used for the protective grounding terminal. There is a possibility of
electrical
shock if the Touch Panel is not grounded.
・
Use and store the Touch Panel in the environment described in the specifications (regarding temperature,
humidity, vibrations, shock, etc).
・
Do not use the Touch Panel where it is subjected to flammable or explosive gases, or stream.
・
Do not disassemble or modify the Touch Panel. Doing so can cause malfunctions and lead to other problems.
・
Do not press on the Touch Panel with screwdrivers or other sharp objects and do not strike it with hard objects.
Doing so can damage the Touch Panel or cause malfunctions.
如图所示方法来连接触摸屏和 PLC
。
触摸屏上电
(Provide Power to the Touch Panel)
作图软件的安装、使用和传送
(Install the Software, Develop and Transfer)
Quick Start Guide
Press “System Setup”
PLC
与
EA7E
的连接
(Connect Touch Panel to PLC)
7
Connect the Touch Panel to PLC as shown.
规格认证
(Agency Approval)
The Touch Panel conforms to CE. Please refer to the product label. Refer to our web site for the latest
information.
。
2
Install Optional Accessories. Please refer to each Manual for
the details. The Manuals can be downloaded from our Web Site.
EA7E
Touch Panel
EA7E 触摸屏
EA-AC
AC 电源模块
EA-AC
AC Power Module
选购件安装
(Install Optional Accessories)
选件的安装。详细内容请参照各自的手册资料。
你可以在选件包中找到手册资料，或者可以去我们的网站上下载手册资料。
PWR
CPU
TxD
RxD
BATT
IOlOl–PLC
CPU Status LED (Green, Orange & Red)
EA7E背面
(Rear View)
EA7E 状态指示 LED (EA7E Status LED)
Off
Green
Red
Orange
Power off
Normal-CPU Run State
On Power On
On Comm. is active
PWR
CPU
TxD
RxD
BATT
IOlOl–PLC
CPU Status LED (Green, Orange & Red)
Off
Green
Red
Power off
Normal-CPU Run State
On Power On
On Comm. is active
1). DC接入(DC Wiring)
(DC20.4~28.8V)
DC24V
+20
％
-15
％
+
-
GND
・
Wire range: Solid: 0.2
～2.5mm
²
Stranded: 0.2～2.5mm, AWG:24～12
・
Screw Torque (terminal) :
Connecting Screw:0.5
～0.6Nm
12
9
3
6
Adjust Clock
CancelOK
etaDemiT
10 : 45 : 23 09 - 01 - 2005
MAIN MENU
Information Setting
Test Menu Memory
Exit
Setting
Adjust Clock Adjust Display
Adjust Touch Panel Beeper
Main Menu
Package includes;
DC Power Connection
Packing Material
包装材料
Mounting Bracket
安装夹具
Quick Start Guide
EA7E TouchPanel
感谢您选用光洋EA7E系列工业触摸屏，在您使用此产品之前，请先阅读本随机说明。如您在
使用此产品时有任何的问题，请联系我们！
Thank you for purchasing our EA7E series Touch Panel. Please read this Quick Start Guide carefully
before applying the product. If you need any help when you use the product, please consult us.
KOYO ELECTRONICS (WUXI) CO., LTD.
地址：中国江苏省无锡市滨湖区建筑西路599号1栋21层
Addr：21st Floor, Building 1, No.599, Jianzhuxi Road, Binhu District, Wuxi, Jiangsu, P.R.China
邮编(Pc)： 214072
电话(Tel)：（0510）85167888
传真(Fax)：（0510）85161393
Homepage:http://www.koyoele.com.cn
EA7E series
・
请不要把触摸屏作为与人的安全或重大伤害有关的开关来使用。（如紧急安全开关等）
・
保护接地端子务必请按第
D
种方法接地，否则有产生电击的可能。
・
请在规定的环境范围（温度、湿度、振动、冲击等）内存放、使用触摸屏。
・
请不要在有可燃性、爆炸性气体或蒸气的场所使用触摸屏。
・
请不要自己分解、改造触摸屏，否则有可能引起故障和其它的问题。
・
不要用硬的东西或螺丝刀的尖头等锋利的东西去敲打触摸屏，以免造成触摸屏的损坏或人身的伤害。
※1：Device is not available on EA7E-TW10CL-RC/RCW 、 EA7E-TW7CL-RC/RCW and EA7E-TW4CL-C/CW.
※1：
EA7E-TW10CL-RC/RCW EA7E-TW7CL-RC/RCW 和 EA7E-TW4CL-C/CW 上没有该接口。
1 8
21
3
4
2
1
3
4
8 1
15 9
Pin Signal
1 Frame GND
TXD (232C)
RXD (232C)
Vcc
2
3
4
5 Logic GND
Pin Signal Pin Signal
6 LE
CTS (232C)
RTS (232C)
RXD+ (422/485)
7
8
9
10 RXD– (422/485)
11 TXD+ (422/485)
TXD– (422/485)
Term. Resistor
do not use
12
13
14
15 do not use
Pin Signal
1 TD+
TD–
RD+
do not use
2
3
4
Pin Signal
5 do not use
RD–
do not use
do not use
6
7
8
Pin Signal
1 Vbus
D–
D+
GND
2
3
4
ShieldShell
Network Activity LED (Orange)
On Active Network Data
Network IdleOff
Link Status LED (Green)
On Ehternet Linked
No Ethernet Comm.Off
1 8
21
3
4
2
1
3
4
8 1
15 9
Pin Signal
1 Frame GND
TXD (232C)
RXD (232C)
Vcc
2
3
4
5 Logic GND
Pin Signal Pin Signal
6 LE
CTS (232C)
RTS (232C)
RXD+ (422/485)
7
8
9
10 RXD– (422/485)
11 TXD+ (422/485)
TXD– (422/485)
Term. Resistor
do not use
12
13
14
15 do not use
Pin Signal
1 TD+
TD–
RD+
do not use
2
3
4
Pin Signal
5 do not use
RD–
do not use
do not use
6
7
8
Pin Signal
1 do not use
D–
D+
GND
2
3
4
Pin Signal
1 do not use
D–
D+
GND
2
3
4
Pin Signal
1 Vbus
D–
D+
GND
2
3
4
ShieldShell
Network Activity LED (Orange)
On Active Network Data
Network IdleOff
Link Status LED (Green)
On Ehternet Linked
No Ethernet Comm.Off
音频输出口(无源）
Audio Line Out 3.5mm Mini Jack (Amplifier Required)
PLC 串行通讯口
PLC Serial Communication
将来使用
For Future Use
EA7E底部视角
Bottom View
Ethernet 10Base-T/100 Base-TX
以太网口：PLC通讯与编程用
PLC Communications & Programming
USB口 B型( 编程用 )
USB Type B (For Programming)
USB口
A
(
USB
设备用 )
USB Type A (For USB Device)
※1
※2
紧固扭矩 Screw Torque:0.3Nm
本触摸屏已取得CE 认证 , 请参考产品上的标签。请浏览本公司网站以获得最新的情报。
请确认包装纸箱中有下图所示的物品。
如果有任何的缺少或损坏，请与您的供货商联系。
随机手册
EA7E本体
其他附件
DC电源接头
4.3寸以外的型号（Except 4.3″Model）
4.3寸型号（4.3″Model）
DL06 PLC
Port 2
EA-2CBL-1
1. 串行口连接
(Serial Connection)
DL06 PLC
H0-ECOM/ECOM100
5类交叉线
Category 5 Cross Cable
Ethernet Port
以太网口
2. 以太网交叉电缆连接
（Ethernet Cross Cable Connection)
100
1
0/
U
pli
nk Port
LN
K
ACT
/
+
1
L
NK
ACT
/
100
10/
P
WR
–
PWR
L
NK
A
C
T/
1
00
10
/ AC
T
/
100
10
/ 10/
AC
T
/
L
N
K
P
WR
2 3
L
NK 100
E–SW05U
DL06 PLC
H0-ECOM/ECOM100
Category 5 Straight Cables
Ethernet Port
以太网口
3.以太网HUB连接
（Ethernet HUB Connection)
*
包括交换式HUB
* Include Switching HUB
5类直连线
100
10/
Up
link Port
LNK
ACT/
+
1
LNK
ACT/
10
0
10
/
PWR
–
P
WR
LN
K
AC
T/
100
10/ A
CT
/
100
10/ 10/
ACT/
LNK
PWR
2
3
LNK 10
0
E–SW05U
PC
Ethernet Port
以太网口
Category 5 Straight Cables
5类直连线
Ethernet Port
以太网口
* Include Switching HUB
* 包括交换式HUB
3. 以太网HUB连接
(Ethernet HUB Connection)
PC
USB口 B型 ( 编程用 )
USB Type B (For Programming)
USB口 A型
USB Type A
USB 电缆
USB Cable
1. USB 连接
(USB Connection)
Clicking or double-clicking the Installer downloaded.
Install
KEW EA7E
programming software in accordance to the message of an installer.
Then start up
KEW EA7E
programming software.
Your system can be easily started up at three steps, “Start” > “Simulate” > “Send” .
点击或双击下载的安装文件。根据提示信息安装
KEW EA7E
作图软件。
通过 “ 开始>模拟>传送 ” 这简单的三步，
※2：Device is not available on EA7E-TW10CL-RC/RCW and EA7E-TW7CL-RC/RCW .
※2：
EA7E-TW10CL-RC/RCW、 EA7E-TW7CL-RC/RCW 上没有该接口。
注：图例为10.2″及7.0″屏的外观，与4.3″屏有所不同。
注：EA-AC电源模块不适用于4.3寸屏。（EA-AC does not adapt to 4.3″Model.）
The ports’ position of 4.3″Model is different.
本触摸屏有 DC24V 和 AC 2 种供电方法。当使用 AC 供电时，需要另外选购电源选件（EA-AC）。
1. 按图 1 所示连接 DC24 电源（4.3寸屏可连接DC12~24V电源）。
2. 按图 2 所示，通过 EA-AC 选件连接 AC100~240V 电源。（4.3寸屏不支持）
5
PC
(Ethernet Cross Cable Connection)
Ethernet Port
以太网口
Ethernet Port
以太网口
2. 以太网交叉电缆连接
Category 5 Cross Cable
5类交叉线
4.3寸以外的型号如下图（Excpet 4.3″ Model）
4.3寸型号如下图（4.3″ Model）
System not found
Low Power
海绵衬垫等
Gasket
DC10.8~28.8V
GND
+
-
･端子台法兰紧固扭矩
※1 4.3″屏无端子台法兰
:
0.4
～
0.5Nm ※1
Screw for flange :0.4～0.5Nm ※1
启动安装好的KEW EA7E
作图软件，
您就可以开始制作您的用户画面了。
KEW-M9213C
※1 No flange for 4.3″ Model
・请在电源断开的情况下连接电源线，否则有可能损坏触摸屏或导致人身伤害。
・
Please connect the power wires when the power is OFF. Otherwise the Touch Panel damage or personal injuny
may be caused.
Quick Start Guide
随机手册
Mounting Bracket
安装夹具
EA7E TouchPanel
EA7E本体
Packing Material
包装材料
Package includes;
DC Power Connection
其他附件
海绵衬垫等
Gasket
DC电源插头
型
To Next Page
Need help?
General