KRAFT KF-MDS10146W - User Manual

Questions and Answers

M
Michael JimenezAug 14, 2025
Why is my KRAFT Washer vibrating and making noise?
- J
  Jenny CherryAug 14, 2025
  Your KRAFT Washer may be vibrating or making noise due to several reasons: it might be standing unbalanced (adjust the feet to level the machine), a hard substance may have entered the pump filter (clean the pump filter), the transportation safety bolts may not have been removed (remove the transportation safety bolts), the laundry quantity might be too little (add more laundry), or the machine might be overloaded (take out some laundry or distribute the load evenly).
C
cookeamyAug 18, 2025
What to do if KRAFT Washer program does not start after closing the door?
- G
  Glenn PalmerAug 18, 2025
  If the program on your KRAFT Washer doesn't start after closing the door, it could be because the Start / Pause button was not pressed (press the Start / Pause button). Alternatively, the washing machine may have switched to self-protection mode due to a supply problem. To cancel the program, turn the Programme Selection knob to select another program. The previous program will be canceled.
D
Deanna PerkinsAug 21, 2025
What to do if my KRAFT Washer displays E 2 - Door lock malfunction?
- M
  michele56Aug 21, 2025
  If your KRAFT Washer displays 'E 2 - Door lock malfunction', it indicates that the door is not closed properly, or the door lock is not working normally. Try closing the door again. Turn off the power by pressing the POWER button, then press the POWER button again, followed by the START/PAUSE button to restart the program.
J
Jamie MontoyaAug 25, 2025
What to do if my laundry remains wet after KRAFT Washer program ends?
- A
  Amy BarryAug 25, 2025
  If your laundry remains wet after the KRAFT Washer program finishes, it's possible that excessive foam occurred due to using too much detergent, which activated the automatic foam absorption system. To resolve this, use the recommended amount of detergent in future washes.
K
Kiara HowardAug 28, 2025
What to do if my KRAFT KF-MDS10146W stopped shortly after the programme started?
- C
  Cassandra CarlsonAug 28, 2025
  If your KRAFT Washer stopped shortly after the program started, it might have stopped temporarily due to low voltage. It will resume running when the voltage restores to the normal level.
H
Holly TorresAug 31, 2025
What to do if my KRAFT Washer displays UNB - UNBALANCE NO SPIN?
- L
  Lauren SmithAug 31, 2025
  Switch off the KRAFT Washer, reload the laundry, switch it on again, and restart the program.
J
James ColeSep 3, 2025
What to do if my KRAFT KF-MDS10146W displays E 4 - Abnormal water drainage?
- L
  Leslie HarrisSep 3, 2025
  Clean the pump filter of your KRAFT Washer. Also, check if the drain hose is bent, twisted, or blocked, and eliminate these issues.
T
tabitha78Sep 6, 2025
What to do if my KRAFT KF-MDS10146W Washer displays E 6 - Heating failure?
- B
  Brittany LewisSep 7, 2025
  Press the START/PAUSE button on your KRAFT Washer to suspend the operation and wait for several minutes. When the temperature in the drum drops to a safe range and the fault code on the display is removed, press the START/PAUSE button to continue the rest of the program.
C
carolyn33Sep 10, 2025
What to do if my KRAFT Washer displays E 3 - Motor failure?
- D
  Debbie ReynoldsSep 12, 2025
  Switch off the KRAFT Washer, wait until it has cooled down, and switch it on again after troubleshooting.