What to do if Kress Robotik MISSION KR233E MissionTM RTKn doesn't start?
If your Kress Robotik MissionTM RTKn doesn't start after pressing the start button, it could be due to two reasons. First, the MissionTM RTKn might be outside the working area; move it inside. Second, there might be a poor positioning signal. In this case, find an open place, wait for the positioning signal light to turn green, and then press the start button.
Why Kress Robotik MISSION KR233E MissionTM RTKn doesn't return to charging base?
If your Kress Robotik MissionTM RTKn runs out of power and doesn't return to the charging base, there are a couple of potential causes: 1. A virtual charging base hasn't been mapped. To fix this, rebuild the map and add the virtual charging base. 2. The magnetic strip is shorter than 2.5 m. Ensure the magnetic strip is longer than 2.5 meters.
What to do if Kress Robotik Lawn and Garden Equipment MissionTM RTKn doesn't alarm outside Geo fence?
If your Kress Robotik MissionTM RTKn doesn't alarm when outside the Geo fence, it could be because: 1. The software isn't up to date. Update the software of the MissionTM RTKn. 2. The MissionTM RTKn is powered off. Turn the MissionTM RTKn on.
What to do if Kress Robotik Lawn and Garden Equipment MissionTM RTKn is stuck on obstacle?
If your Kress Robotik MissionTM RTKn is parked in the middle of an obstacle, consider these possible causes: 1. The obstacles are too small for MissionTM RTKn to navigate. Set the area where MissionTM RTKn gets easily trapped as No-Go. 2. The sensor of MissionTM RTKn is abnormal. Detect MissionTM RTKn's diagnostic page on the APP and check the sensor status.
Why Kress Robotik MISSION KR233E Lawn and Garden Equipment MissionTM RTKn parked near wall and won't start?
If your Kress Robotik MissionTM RTKn is parked around the wall, cannot be started, and the positioning light is always on red, it may be due to the MissionTM RTKn working in the shaded area for too long, triggering the safety protection. Try to avoid letting MissionTM RTKn mow in areas with too much shade.
What to do if Kress Robotik MISSION KR233E Lawn and Garden Equipment MissionTM RTKn overruns boundary downhill?
If your Kress Robotik MissionTM RTKn overruns the boundary line when going downhill, it might be because the angle of the border line is very sharp. Try to avoid layout scenarios with sharp angles.
Why Kress Robotik MISSION KR233E Lawn and Garden Equipment charging base LED is off?
If the LED light on the charging base of your Kress Robotik Lawn and Garden Equipment does not turn on, it is likely due to a lack of power. Check that the charging base is properly connected to the charger and that the charger is connected to a suitable power supply.
Read all safety warnings and instructions to avoid electric shock, fire, and serious injury.
Understand instructions, know controls, and ensure safe operation by trained personnel for accident prevention.
Confirm virtual boundary, inspect area for foreign objects, and check blade assembly for wear or damage.
Step-by-step guide to safely remove and replace the lawnmower blades using the correct tools and screws.
Flip the mower, clean the blade disc, chassis, and wheels with a brush or moist rag, ensuring free blade rotation.
Periodically clean charging pins and strips on the base and mower to ensure successful charging.
General| Cutting Height | 30-60 mm |
|---|---|
| Battery Voltage | 20 V |
| Typical Working Time on One Charge | 60 min |
| Charging Time | 60 min |
| Engine Type | Brushless |
| Cutting Height Adjustment | Manual |
| Battery Capacity | 4 Ah |
| Warranty | 3 years |
To Next Page
