What to do if my KRESS Vacuum Cleaner is not operating at the correct time?
If your KRESS Vacuum Cleaner is not operating at the correct time: * The clock may not be set to the correct time; set the clock accordingly. * Programmed cutting times may be incorrect; change the time settings for the mower to start and stop. * The Vacuum Cleaner may be manually docked in the charging base; press START and then OK.
What does it mean if the green light is flashing on the charging base of my KRESS Mission KR110 Vacuum Cleaner?
If the green light is flashing on the charging base of your KRESS Vacuum Cleaner, the boundary wire isn’t connected. Check that the boundary wire has been connected correctly to the charging base and that there are no breaks in the boundary wire, especially at the wire ends.
Why does my KRESS Mission KR110 Vacuum Cleaner run outside the boundary wire?
Your KRESS Vacuum Cleaner may run outside the boundary wire, fail to mow within a boundary wire zone, or reverse/rotate erratically near the boundary wire due to: * The boundary wire of another Vacuum Cleaner being positioned too closely; ensure at least 1m of spacing between neighboring boundary wires. * The boundary wire being installed with tight corners; ensure the corners are smooth. * Wet conditions causing electric signal leakage at wire joints; check and insulate boundary wire joints for a waterproof connection. * Broken insulation causing electric signal leakage; repair damaged insulation with insulation tape. * The cutting area being larger than allowable; contact a service agent.
What does it mean if the green light on the charging base of my KRESS Vacuum Cleaner turns on before charging is complete?
If the green light on the charging base of your KRESS Vacuum Cleaner turns on before charging is complete, the charging base is likely overheating. The LED will display 'Battery charge overtemp! Please wait cooling down'. Place the charging base in a shady area or wait until the temperature has cooled down.
What to do if my KRESS Mission KR110 Vacuum Cleaner exits the boundary wire due to high speed when going down a hill?
If your KRESS Vacuum Cleaner exits the boundary wire due to high speed when going down a hill, the boundary wire is likely placed on a slope steeper than 17% (10°). Reposition the boundary wire away from slopes steeper than this. Refer to the Installation Guide for details.
Why does my KRESS Vacuum Cleaner turn on, but the blade disc does not move?
If your KRESS Vacuum Cleaner turns on but the blade disc does not move, it is likely searching for the charging base (unless you pressed the HOME button or the 'Border cut' function is operating). This is normal; the blade disc does not rotate while it is automatically searching for the charging base to recharge.
General| Brand | KRESS |
|---|---|
| Model | Mission KR110 |
| Category | Vacuum Cleaner |
| Language | English |
Essential safety warnings and guidelines for operating the robotic lawnmower.
Detailed safety information, warnings, and symbols for operating the robotic lawnmower.
General operation procedures and safety precautions for the robotic lawnmower.
Specific instructions for automatic operation and unattended use of the lawnmower.
Recommendation for connecting to a supply circuit protected by an RCD.
Information on residual risks and protective measures.
Instructions for safely transporting the robotic lawnmower.
Crucial safety warnings regarding the handling and storage of the battery pack.
Specifications and technical details for KR110 and KR111 models.
Information regarding the sound pressure and sound power levels of the robotic lawnmower.
Explanation of how the robotic lawnmower determines its mowing direction and pattern.
Details on how the lawnmower navigates, finds the charging base, and uses sensors.
How the robotic lawnmower's design allows for cutting close to boundaries and walls.
Factors affecting mowing efficiency and how to adjust settings for optimal performance.
Guidance on using the distance gauge to correctly install the boundary wire around the lawn.
Recommended steps for burying the boundary wire after installation and testing.
Instructions on how to properly splice and connect boundary wires using connectors.
Instructions for maintaining the sharpness of the cutting blades and their replacement.
Procedures for cleaning the robotic lawnmower's body and underside for optimal performance.
Information on the battery, its storage, and factors affecting its lifespan.
Recommendations for preparing and storing the robotic lawnmower for winter.
Step-by-step guide for safely replacing the battery in the robotic lawnmower.
To Next Page