Krystal Pure KR10 - User Manual

Questions and Answers

H
hurleykimberlyAug 16, 2025
Why is my Krystal Pure KR10 ice maker not working?
- A
  Antonio JensenAug 16, 2025
  If your Krystal Pure Water System's ice maker isn't working, first, ensure the ball valve to the ice line is turned on and the ice maker in your refrigerator is in the 'on' position. If the ice maker line is frozen, thaw it using a hair dryer, ensuring you have a full tank of water before turning the ice maker back on. Also, check for any kinks in the tube leading to the refrigerator and repair them.
D
Daniel AlexanderAug 18, 2025
How to fix little water flow from Krystal Pure KR10 faucet?
- T
  Tamara FuentesAug 18, 2025
  If you're getting very little water from your Krystal Pure Water System faucet, several factors could be at play. First, check the tank pressure; when empty, it should be between 5-12 PSI. Ensure your incoming water pressure is at least 40 PSI; if it's lower, you may need a pump to increase it. If you have a new system or have just changed the filters, remember that it can take 4 to 12 hours to completely fill the tank. Other potential issues include a bad check valve (which would need replacement), a closed tank valve (ensure it's open), a faulty storage tank (replace if necessary, and check air pressure when empty), clogged filters (replace them), or a kinked tube (un-kink or replace if damaged).
R
reginaldjonesAug 22, 2025
What to do if no water comes out of the refrigerator door with my Krystal Pure Water System?
- W
  wintersrobertAug 22, 2025
  If water is not coming out of the refrigerator door from your Krystal Pure Water System, ensure the 1-quart reservoir is full by holding down the dispenser handle for about 3 minutes until water flows. Also, make sure the R/O tank is full.
E
Eric MorrisonAug 25, 2025
Why does my Krystal Pure Water System make water so slowly?
- N
  nathan10Aug 26, 2025
  If your Krystal Pure Water System is making water slowly, it's important to remember that R/O systems make water a drop at a time, and a 3-gallon storage tank typically fills in 4-12 hours. If the process seems excessively slow, check if your city water pressure is low and increase it to 40 PSI with a booster pump if needed. Inspect the tubing for any kinks and repair them. Also, consider whether the filters are plugged and need replacement, or if the membrane is failing and needs to be replaced.
W
williamhubbardAug 27, 2025
Why is my Krystal Pure KR10 continually running?
- A
  April WrightAug 28, 2025
  If your Krystal Pure Water System is continually running, the shut-off valve may not be working correctly and needs to be replaced.
T
Toni LopezAug 31, 2025
How to fix bad taste or smell from Krystal Pure KR10 Water System?
- R
  romanstevenAug 31, 2025
  If the water from your Krystal Pure Water System doesn't taste or smell right, the filters may have expired and need replacement, typically every 6 to 12 months. If you use little water, drain or use the entire tank every 2 weeks. The system may also need sanitizing; follow the recommended sanitizing instructions and replace the filters.
J
jalexanderSep 2, 2025
Why are my Krystal Pure KR10 Water System ice cubes cloudy?
- C
  Christopher GonzalezSep 2, 2025
  Cloudy ice cubes or milky colored water from your Krystal Pure Water System can be due to several reasons. It could be a bad membrane, in which case you should replace the membrane and sanitize when rejection is below 75%. High oxygen content in the water supply can also cause this issue. Sometimes, the refrigerator's freezing process can make ice cubes appear cloudy; if this is the case, let the cube dissolve in a glass of water to see if it's just air. If your system is new, this is normal and should clear up within two weeks.
R
Ryan BuchananSep 6, 2025
Why is my Krystal Pure Water System drain or faucet so noisy?
- P
  pagematthewSep 6, 2025
  A noisy drain or faucet in your Krystal Pure Water System could be due to a few reasons. If you have an air gap faucet, some noise is normal; ensure it's installed in the proper location according to the manual and allow two weeks for air to work out of the system. Also, check that the drain tube from the faucet runs continuously downhill to the drain, as loops or dips can cause noise. Disconnect the drain tube and clean it to remove any debris.
M
Mark CarpenterSep 9, 2025
What to do if hole on Krystal Pure KR10 faucet is leaking?
- T
  Thomas SmithSep 9, 2025
  If the hole on your Krystal Pure Water System faucet is leaking, it could be due to a few reasons. If the drain tube has loops or dips, shorten it to ensure a smooth downhill flow to the drain. A restriction in the drain tube could also be the cause; disconnect and clean it out. Additionally, check the O-ring for proper sealing; if it's damaged, replace it; if it's dirty, clean, lubricate, and retighten the filter bowl.
M
Margaret ArmstrongSep 12, 2025
Why is my Krystal Pure KR10 Water System filter bowl canister leaking?
- L
  Linda NortonSep 12, 2025
  If your Krystal Pure Water System's filter bowl canister is leaking, hand tighten it firmly. If the issue persists, the membrane might be bad and needs replacement, especially if rejection is below 75%. Sanitizing the system might also be necessary.

Summary

Specifications and Safety Guidelines

Safety Warnings

Highlights critical safety precautions and warnings for system operation and installation.

Installation Procedures

Step 1: Position System

Guidance on selecting the optimal location for the R/O system components under the sink.

Step 2: Faucet Installation

Detailed instructions for installing the dedicated faucet on the sink.

Step 3: Easy Tap Adapter Installation

Procedure for connecting the system to the cold water supply using an easy tap adapter.

Step 4: Drain Saddle Clamp Installation

Instructions for installing the drain saddle clamp onto the sink's drainpipe.

Step 5: Storage Tank Preparation

Step 6: Tubing Connections

Step 7: System Start-Up Procedures

Steps to follow for initial system activation, flushing, and leak checking.

Step 8: Refrigerator Ice Maker Hook Up

Step 9: Recommended Filter Service Life

Step 10: Filter Changing Procedures

Step 11: Recommended Sanitizing Procedure

Step 12: Service and Maintenance Recommendations

Maintenance, Parts, and Troubleshooting

Trouble Shooting Guide

Identifies common problems and provides solutions for the R/O system.

Warranty and Registration

Manufacturers Warranty

Krystal Pure KR10 Specifications

General

Filtration Technology	Reverse Osmosis (RO)
Stages of Filtration	5
Weight	15 lbs
Operating Temperature	40-100°F
Power Supply	Not required (non-electric)
Filter Life	6-12 months (depending on usage)