What to do if my Krystal Pure KS15HE Water Dispenser is not providing soft water after regeneration?
If your Krystal Pure Water Dispenser isn't providing soft water after regeneration, there might be a few reasons. First, check the power source to ensure the unit is regenerating. Second, make sure there is enough salt in the brine tank; if not, add salt. Lastly, the injector might be clogged, so clean the injector and drain with water.
Why is my Krystal Pure KS15HE using more or less salt than the control setting?
If your Krystal Pure Water Dispenser uses the wrong amount of salt, it could be due to incorrect settings; ensure you have the correct adjustments. Foreign material might also be causing incorrect flow rates in the control. Remove the variable salt control and flush out any foreign matter. Manually position the control to 'brine draw' to clean it, then to 'purge' to remove brine from the tank. If these steps don't resolve the issue, the control itself may be defective and need replacement.
What to do if my Krystal Pure KS15HE Water Dispenser control does not draw brine?
If the control of your Krystal Pure Water Dispenser isn't drawing brine, it could be due to several reasons. First, low water pressure may be the cause; adjust the pump to maintain the conditioner at 30 PSI. There might be a restriction in the drain line, so remove any obstructions. Also, the injector could be clogged, so clean the injector and the presentation window. If the injector is defective, replace it. Lastly, valve 2 or 4 might not be closed; remove any foreign materials from the disc and check if the disc closes by pushing on the stem. Replace if necessary.
What to do if there is overflowing in the brine tank of my Krystal Pure KS15HE?
If your Krystal Pure Water Dispenser's brine tank is overflowing, it might be because the brine valve (1) is open; manually operate the valve stem to remove any obstruction. The brine flow rate may also be uncontrolled; remove the variable salt control to clean it. Another cause could be that valve 3 or 4 isn't closed when brine is being drawn, causing refill; remove any foreign material keeping the disc open and manually operate the valve stem. Finally, check all brine line connections for air leaks.
Why is the backwash frequency of my Krystal Pure Water Dispenser control too high or too low?
If the backwash frequency of your Krystal Pure Water Dispenser control is too high or too low, the backwash control might be incorrect; replace it with the correct size control. Also, foreign material might be affecting the control's operation; remove the controller and ball, then drain with water.
What to do if there's intermittent or irregular brine draw in my Krystal Pure KS15HE Water Dispenser?
If your Krystal Pure Water Dispenser is experiencing intermittent or irregular brine draw, low water pressure could be the cause; adjust the pump to maintain the softener/conditioner at 30 PSI. Additionally, a defective injector may be the problem; replace the injector and the injector cap.
Why is there constant water flow and dripping in the drain or brine line of my Krystal Pure KS15HE after regeneration?
If you notice continuous water flow and dripping in the drain or brine line of your Krystal Pure Water Dispenser after regeneration, the drain valve (5 or 6) or the brine valve (1) might be open due to foreign material or particles; manually operate the valve stem to remove the obstruction. Alternatively, the return spring on the valve stem in the top plate could be weak; replace the spring.
Critical safety precautions for installation, operation, and maintenance to prevent damage or injury.
Diagnosing and resolving issues related to the control valve's operation.
Specific troubleshooting for KS5 and KS10 control unit problems like clock display.
Resolving common control system problems like flow display or regeneration timing.
General| Cold Water Temperature | 5-10°C |
|---|---|
| Voltage | 220-240V |
| Weight | 12 kg |
| Type | Water Dispenser |
| Material | Plastic |
| Certification | CE |
To Next Page
