Why is my KTM 790 ADVENTURE R 2022 using so much oil?
If your KTM Motorcycle has high oil consumption, the engine vent hose might be bent; route it without bends or replace it if necessary. The engine oil level could also be too high; check it. Alternatively, the engine oil might be too thin (low viscosity); change the engine oil and the oil filter, and clean the oil screens.
Why is the battery dead on my KTM 790 ADVENTURE R 2022 Motorcycle?
If the 12-V battery is discharged on your KTM Motorcycle, it may be because the ignition was not switched off when the vehicle was parked; charge the 12-V battery. Alternatively, the 12-V battery may not be charging by the alternator; check the charging voltage.
What to do if my KTM 790 ADVENTURE R 2022 engine does not turn over?
If your KTM Motorcycle engine doesn't turn when you press the start button, several factors could be at play. You might be making an operating error, so ensure you're following the correct start procedure. Alternatively, the 12-V battery could be discharged, requiring a charge and check of the open-circuit current. Also, check if fuse 1, 2, or 3 is blown, and replace them if necessary. The main fuse might also be burned out, so replace it if needed. Lastly, verify that there's a proper ground connection.
Why does my KTM 790 ADVENTURE R 2022 engine have no power?
If your KTM Motorcycle engine has too little power, the air filter might be very dirty; remove and reinstall it. Also, the fuel filter could be very dirty, so check the fuel pressure. A malfunction in the electronic fuel injection could also be the cause; use the KTM diagnostics tool to read out the fault memory.
Why does the ABS warning lamp light up on my KTM Motorcycle?
If the ABS warning lamp lights up on your KTM Motorcycle, the ABS fuse may be blown; replace the ABS fuses. It could also be that the wheel speeds of the front and rear wheels differ greatly; in this case, stop, switch off the ignition, and start again. Finally, there may be a malfunction in the ABS, requiring you to read out the ABS fault memory using the KTM diagnostics tool.
Why does my KTM Motorcycle only start with the clutch in?
If your KTM Motorcycle engine only turns when the clutch lever is drawn, the vehicle is likely in gear. Shift the transmission into neutral. Alternatively, the vehicle might be in gear and the side stand is folded out; in this case, also shift the transmission into neutral.
What to do if my KTM 790 ADVENTURE R 2022 engine dies while riding?
If your KTM Motorcycle engine dies during a trip, it could be due to a lack of fuel; refuel. Alternatively, fuse 1, 2, or 3 might be blown; replace the fuses.
What does it mean if the malfunction indicator lamp is on in my KTM 790 ADVENTURE R 2022 Motorcycle?
If the malfunction indicator lamp lights up or flashes on your KTM Motorcycle, there is likely a malfunction in the electronic fuel injection. You should read out the fault memory using the KTM diagnostics tool.
Why aren't the headlight and position lights working on my KTM 790 ADVENTURE R 2022 Motorcycle?
If the headlight and position light are not functioning on your KTM Motorcycle, fuse 6 may be blown. Replace the fuses.
Why aren't the turn signal, brake light, and horn working on my KTM Motorcycle?
If the turn signal, brake light, and horn are not functional on your KTM Motorcycle, fuse 5 may be blown. Replace the fuses.
General| Brand | KTM |
|---|---|
| Model | 790 ADVENTURE R 2022 |
| Category | Motorcycle |
| Language | English |
Explains the meaning of specific symbols used in the manual.
Explains the typographical formats used in the document.
Defines the intended use and limitations of the vehicle.
Explains the different levels of risk and associated symbols.
Illustrates and labels key components from the front left view.
Locates the Vehicle Identification Number (VIN) on the steering head.
Locates the engine number on the engine case.
Describes the functions of switches on the left handlebar.
Describes the functions of switches on the right handlebar.
Details the procedure for locking the steering mechanism.
Explains how to open the fuel tank filler cap safely.
Identifies the location of the shift lever and gear positions.
Explains the use and safety system coupling of the side stand.
Overview of the instrument cluster and its main areas.
Explains how warning messages are displayed and their meanings.
Lists and explains the various indicator lamps on the instrument.
Details the function and configuration of the shift warning light.
Details the steps for adjusting handlebar position for comfort.
Explains how to adjust the clutch lever position.
Details how to adjust the foot brake lever's basic position.
Offers essential advice before riding the vehicle for the first time.
Advises on proper vehicle loading and weight limits.
Lists pre-ride checks for vehicle roadworthiness.
Explains proper braking techniques and safety warnings.
Provides instructions and safety precautions for refueling.
Lists mandatory maintenance tasks based on time or mileage intervals.
Details how to adjust the fork's compression damping.
Explains how to adjust the fork's rebound damping.
Explains how to adjust the shock absorber's spring preload.
Provides instructions and warnings for cleaning the motorcycle chain.
Explains how to check and set correct chain tension.
Details the procedure for removing the front fender.
Details the procedure for removing the windshield.
Explains the ABS system, its modes, and warnings.
Details how to check the front brake fluid level.
Guides on checking the front brake linings for wear.
Guides on checking the rear brake linings for wear.
Explains the procedure for installing the front wheel.
Explains how to check tire condition, tread depth, and age.
Details how to check and set correct tire pressure.
Details the procedure and safety precautions for removing the 12V battery.
Provides instructions and precautions for charging the 12V battery.
Details how to change the main fuse and its location.
Details how to change fuses for various electrical components.
Explains how to adjust the headlight range for different loads.
Details how to check the coolant level safely.
Explains how to add coolant and bleed the system safely.
Describes the available ride modes and their characteristics.
Explains the function and operation of the MTC system.
Guides on checking the engine oil level at operating temperature.
Details the procedure for changing engine oil and filter.
Explains how to add engine oil and its importance.
Provides instructions for cleaning the motorcycle safely and effectively.
Outlines maintenance for winter storage and protection from salt.
Details steps for preparing the motorcycle for long-term storage.
Lists potential causes and actions for starting issues.
Lists potential causes and actions for engine start failure.
Lists potential causes and actions for engine overheating.
Lists potential causes and actions for malfunction lamp warnings.
Lists potential causes and actions for a blank instrument display.
Lists detailed technical specifications for the engine.
Lists technical specifications for the chassis and suspension.
Lists electrical system specifications including battery and fuses.
Lists fork specifications and adjustment ranges.
Details specifications and recommended suppliers for brake fluid.
Specifies engine oil standards, guidelines, and suppliers.
Provides fuel specifications and ethanol content guidelines.
Lists recommended chain cleaner product.
Lists recommended motorcycle cleaner product.
Lists recommended street chain spray product.
Explains the JASO T903 MA2 standard for motorcycle oils.
Defines MTC as Motorcycle Traction Control reducing engine torque.
Defines TPMS as Tire pressure monitoring system for rider information.
Explains that yellow/orange symbols indicate prompt intervention errors.
To Next Page