EasyManua.ls Logo

Kubota VS 400-VITI - User Manual

Kubota VS 400-VITI
154 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
VS 220/ 400/ 400-VITI/
VS600
User's manual
Edition 09.2013
Date of printing 11.2013
Language EN- USA
Machine number 1001
Type VN223/ VN224/ VN225/ VN226
Document Number VN70051799

Table of Contents

Questions and Answers

  • S
    Sandra DaltonAug 16, 2025
    How to fix incorrect application rates (lbs/acre) with Kubota Spreader?
    • D
      Daniel FranklinAug 16, 2025
      Incorrect application rates with the Kubota Spreader can stem from several causes. Ensure the dosing setting is correct per the instructions and verified with a calibration test. For fine applications, confirm the dosing setting is accurate. Adjust driving speed if it's too high or low, and always set driving tracks before spreading. Remember to determine the characteristics of the fertilizer and set the spreader accordingly, especially when using a new type. If fertilizer flow is blocked, clean the machine after each use and replace a worn agitator. For average quality fertilizer, contact your supplier, improve the storage area, and spread with smaller widths if possible.
  • S
    Sarah FrenchAug 23, 2025
    What to do if there are great amounts of dust while spreading with Kubota Spreader?
    • O
      obradfordAug 23, 2025
      Excessive dust during spreading with the Kubota Spreader can be due to a few reasons. First, check the PTO shaft RPM to ensure it's not too high. Also, ensure the PTO shaft is switched off after closing the dosing to prevent the stirrer from grinding, and inspect the stirrer for any damage. If you're using average quality fertilizer, determine its distribution and spread with smaller working widths if possible.
  • J
    John CraigSep 1, 2025
    Why are there powerful vibrations perceptible in my Kubota Spreader?
    • R
      Ricardo NelsonSep 1, 2025
      Powerful vibrations in the Kubota Spreader can be caused by a stoppage due to a hard object, bridge formation due to wet fertilizer, or the PTO shaft working angle being out of reach. Remove any hard objects causing the stoppage. Break up any bridge formation or replace the fertilizer. Limit the PTO shaft working angle to a maximum of 30º. Shut down the PTO shaft immediately!
  • C
    carpenterchristineNov 8, 2025
    Why are there spreading tracks visible among the crops with my Kubota Spreader?
    • M
      Michael WilliamsonNov 8, 2025
      Spreading tracks among crops when using the Kubota Spreader can occur for several reasons: * Using a blend of fertilizer types that have become unmixed or contain varying spreading qualities. * Using a new type of fertilizer with the same settings as the previous type. * Using the wrong spreading chart. * Working in unfavorable weather conditions like high humidity, rain, heat, or high wind speeds. * Incorrect overlapping of the spreading pattern. * Horizontal or vertical settings of the machine are incorrect. * Spreader not set to the correct height. * Incorrect working width. * Worn or incomplete spreading spout. * Uneven tire pressure. * Reduced RPM of the spreading mechanism due to loss at the safety clutch. To resolve this, check the fertilizer type, pattern, a...

Summary

Preface

Safety

For your safety

General safety instructions and warnings to prevent injury or death during operation.

Warning stickers

Details the importance and location of various warning stickers on the machine.

safety regulations

Specifies requirements and prohibitions for machine usage, maintenance, and repair.

Calculate the axle load with tractor-mounted machines

Provides methods and formulas for calculating axle loads to ensure safe tractor operation.

Hydraulic system

Highlights safety procedures when working with the high-pressure hydraulic system.

Getting familiar with the machine

Adjust carefully

Guides on setting application rate and working width independently for precise application.

Set the application rate (lb;acre)

Explains how to use the regulating rod for accurate adjustment of dosing quantities.

Operating the spreader

Describes manual, hydraulic, and electronic methods for operating the spreader's dosing mechanism.

Assembly instruction

Assembly VS220-330

Step-by-step instructions for assembling the VS220-330 model and its accessories.

VS400-500

Assembly instructions specific to the VS400-500 models, including frame and component mounting.

VS 600 - 1000

Assembly steps for the VS600-1000 models, covering frame, unit, and accessory mounting.

Before first use

Tractor provisions

Mounting the coupling shaft

Checking the coupling shaft length

Setting the safety clutch

To be done before spreading

Online spreading chart service

Finding the correct setting for your spreading work

A step-by-step guide to determine correct settings using data and charts.

Use a slide rule and spreading chart decal

Setting the spreader

Guides on adjusting the spreader settings, including contact with materials and environment protection.

Fine application

Calibration test

Highlights the necessity and procedure for performing calibration tests for accurate settings.

Check the spreading pattern (tray test)

Details the importance and method for performing a tray test to check fertilizer distribution.

Full field spreading pattern test

Driving on the road

Before taking the road

Preparing the machine to be transported

Use on the land

Adjusting the machine

Set driving paths

Spreading

Instructions on initiating spreading, managing dosing units, and handling stoppages.

Border spreading

One-sided boundary spreading with the border spreading plate

Border spreading with the border-spreading cylinder

Failure and stoppage

Guides on identifying causes of failure and stoppage, and safe procedures to resolve them.

Storing the machine

Protect the machine

Cleaning

Disconnecting the machine

Preparation for winter storage

Maintenance

Repair damage safely and without delay

General safety rules to follow before performing any repair or maintenance work.

Performed by an authorised person

Maintenance intervals

Provides a schedule for inspection, lubrication, and replacement tasks based on usage.

Lubricate with oil and grease

Coupling shaft

Maintenance procedures for the coupling shaft, including lubrication and checking components.

Checking the hydraulic system

Guidance on safely inspecting the hydraulic system for leaks and damage.

Torques

Accessories

Calibration container

Border-spreading cylinder

Border spreading plate

Fine application set

Trouble shooting

Troubleshooting table

A comprehensive table listing problems, possible causes, solutions, and corresponding page references.

Incorrect application rates

Kubota VS 400-VITI Specifications

General IconGeneral
BrandKubota
ModelVS 400-VITI
CategorySpreader
LanguageEnglish

Related product manuals