Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 114
auto show processes
Continuously show thread runtime information
bluetooth serial <line>
Enters the bluetooth serial level. <line> = number of the line (bluetooth serial port) to be
configured.
clrscrn
Clears the screen.
configure
Enters the configuration level.
connect
Show name and number for lines.
connect line <line>
Begin session on serial port.
device
Enters the device level.
disable
Exits the enable level.
dns
Enters the DNS level.
email <number>
Enters the configure email level.
exit
Exit from the system
filesystem
Enters the filesystem level.
iperf <params>
Run iperf with command line parameters passed in quoted string.
kill ssh <session>
Kills SSH session with index from "show sessions"
kill telnet <session>
Kills Telnet session with index from "show sessions"
line <line>
Enters the line level. <line> = number of the line (serial port) to be configured.
ping <host>
Ping destination continuously with 5 second timeout
ping <host> <count>
Ping destination n times with 5 second timeout
ping <host> <count>
<timeout>
Ping destination n times with x timeout (in seconds)
ping6 <host>
Ping destination continuously with 5 second timeout
ping6 <host> <count>
Ping destination n times with 5 second timeout
ping6 <host> <count>
<timeout>
Ping destination n times with x timeout (in seconds)
reload
Reboot system
reload factory defaults
Reload factory defaults to permanent storage
reload to standalone
firmware installer
Reboot system to standalone firmware installer
show
Show system information
show history
Displays the last 20 commands entered during the current CLI session.
show interfaces
Show interface statistics
show ip sockets
Show UDP/TCP state information
show lines
Show line information
show multicast routes
show state of VIFs and multicast routing tables
show processes
Show thread runtime information
show routes
show system routing table
show rules
show system rules
show sessions
Show active Telnet and SSH Sessions
ssh
Enters the SSH configuration level.
ssh <optClien-
tUsername> <host>
Begin SSH session on network <host>. The optClientUserName must match an SSH Cli-
ent: Users configuration entry. Use "" in optClientUserName to prompt for host username
and password.
ssh <optClien-
tUsername> <host>
<port>
Begin SSH session on network <host>:<port>. The optClientUserName must match an
SSH Client: Users configuration entry. Use "" in optClientUserName to prompt for host
username and password.
ssl
Enters the SSL configuration level.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm