Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 115
tcpdump <parameters>
dump traffic on a network
telnet <host>
Begin telnet session on network <host>.
telnet <host> <port>
Begin telnet session on network <host>:<port>.
trace route <host>
Trace route to destination
trace route <host> <pro-
tocol>
Trace route to destination using TCP, ICMP, or UDP
tunnel <line>
Enters the tunnel level. <line> = number of the tunnel line (serial port) to be configured.
usb <line>
Enters the usb level. <line> = number of the line (usb port) to be configured.
write
Stores the current configuration in permanent memory.
xml
Enters the XML level.
eth0 link state change (config-action:eth0 link state change) level commands
clrscrn
Clears the screen.
default delay
Resets alarm processing delay to its default value.
delay <seconds>
Sets the delay in processing the alarm. Alarm actions will not be executed if the cause is
corrected within this time.
email
Enters the next lower level.
exit
Exits to the config alarm level.
ftp put
Enters the next lower level.
http post
Enters the next lower level.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show status
Displays statistics.
snmp trap
Enters the next lower level.
write
Stores the current configuration in permanent memory.
failover (config-ethernet-failover:usb0) level commands
clrscrn
Clears the screen.
default failback threshold
Restores the default Failback threshold.
default failover interface
Restores the default Failover interface.
default failover threshold
Restores the default Failover threshold.
default interval
Restores the default Ping interval.
default method
Restores the default ping method.
default timeout
Restores the default Ping response timeout.
exit
Exit back to interface configuration level
failback threshold
<pings>
Sets the Failback threshold. If <pings> attempts are answered, the device will Failback to
original interface.
failover interface <text>
Sets the Failover interface.
failover threshold
<pings>
Sets the Failover threshold. If <pings> attempts go unanswered, the device will Failover to
selected interface.
hostname <text>
Sets the host name. <text> = name of the host to ping.
interval <seconds>
Sets the Ping interval in seconds.
method icmp
Ping using ICMP-ECHO.
method tcp
Ping using TCP.
no hostname
Clears the host name.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show status
Show failover status

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm