Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 117
hostname <text>
Sets the host name. <text> = name of the host to ping.
interval <seconds>
Sets the Ping interval in seconds.
method icmp
Ping using ICMP-ECHO.
method tcp
Ping using TCP.
no hostname
Clears the host name.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show status
Show failover status
state disable
Disables Failover.
state enable
Enables Failover.
test
Test failover configuration
timeout <seconds>
Sets the Ping response timeout in seconds.
write
Stores the current configuration in permanent memory.
filesystem (filesystem) level commands
cat <file>
Show the contents of a file
cd <directory>
Change the current directory to the specified directory
clrscrn
Clears the screen.
cp <source file> <desti-
nation file>
Copy an existing file
dump <file>
Show contents of a file as a hex dump
exit
Exits to the enable level.
format
Format the file system and lose all data
ls
Show all files and directories in the current directory
ls <directory>
Show all files and directories in the specified directory
mass storage
Enters the next lower level.
mkdir <directory>
Create a directory
mv <source file> <desti-
nation file>
Move a file on the file system
pwd
Print working directory
rm <file>
Remove a file
rmdir <directory>
Remove a directory
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show statistics
Show file system statistics
show tree
Show all files and directories from current directory
tftp get <source file>
<destination file> <host>
Get a file using TFTP
tftp get <source file>
<destination file> <host>
<port>
Get a file using TFTP
tftp put <source file>
<destination file> <host>
Put a file using TFTP
tftp put <source file>
<destination file> <host>
<port>
Put a file using TFTP
touch <file>
Create a file
filter 1 (config-ethernet-qos-filter:usb0:1) level commands

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm