Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 370
wlan0 link state change (config-action:wlan0 link state change) level commands
clrscrn
Clears the screen.
default delay
Resets alarm processing delay to its default value.
delay <seconds>
Sets the delay in processing the alarm. Alarm actions will not be executed if the cause is
corrected within this time.
email
Enters the next lower level.
exit
Exits to the config alarm level.
ftp put
Enters the next lower level.
http post
Enters the next lower level.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show status
Displays statistics.
snmp trap
Enters the next lower level.
write
Stores the current configuration in permanent memory.
wpax (config-profile-security-wpax:default_infrastructure_profile) level commands
apply wlan
Try out WLAN settings without saving them to Flash. If the settings do not work, when you
reboot the device, it will still have the original settings.
authentication 802.1x
Sets the authentication method to IEEE 802.1x.
authentication psk
Sets the authentication method to PSK.
clrscrn
Clears the screen.
credentials <text>
Selects the RSA certificate by configured name.
default authentication
Restores the authentication method to the default value (PSK).
default eap-ttls option
Restores the EAP-TTLS protocol options to the default (EAP-MSCHAP V2).
default fast option
Restores the FAST authentication protocol option to the default (MD5).
default fast provisioning
Restores the FAST provisioning to the default (Authenticated).
default ieee 802.1x
Restores the default IEEE 802.1x protocol, EAP-TTLS.
default peap option
Restores the PEAP authentication protocol options to the default (EAP-MSCHAP V2).
default pmf
Restores PMF to the default value (Disabled).
eap-ttls option chap
Sets the EAP-TTLS authentication protocol option to CHAP.
eap-ttls option eap-md5
Sets the EAP-TTLS authentication protocol option to EAP-MD5.
eap-ttls option eap-
mschapv2
Sets the EAP-TTLS authentication protocol option to EAP-MSCHAP V2.
eap-ttls option mschap
Sets the EAP-TTLS authentication protocol option to MSCHAP.
eap-ttls option mschapv2
Sets the EAP-TTLS authentication protocol option to MSCHAP V2.
eap-ttls option pap
Sets the EAP-TTLS authentication protocol option to PAP.
exit
Exits to the next higher level.
fast option gtc
Sets the FAST authentication protocol option to GTC.
fast option md5
Sets the FAST authentication protocol option to MD5.
fast option mschapv2
Sets the FAST authentication protocol option to MSCHAPv2.
fast provisioning authen-
ticated
Sets the FAST provisioning option to Authenticated.
fast provisioning both
Sets the FAST provisioning option to Both.
fast provisioning unau-
thenticated
Sets the FAST provisioning option to Unauthenticated.
ieee 802.1x eap-tls
Sets the IEEE 802.1x protocol to EAP-TLS.
ieee 802.1x eap-ttls
Sets the IEEE 802.1x protocol to EAP-TTLS.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm