Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 99
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
stop character <control>
Sets the stop character. The character may be input as text, control, decimal, or hex. A
control character has the form <control>C. A decimal value character has the form \99. A
hex value character has the form 0xFF.
timeout <milliseconds>
Disconnects when no data has been received on the line (serial port) for the specified
length of time. <milliseconds> = timeout in milliseconds.
write
Stores the current configuration in permanent memory.
discovery (config-discovery) level commands
clear counters
Zeros Query Port counters
clrscrn
Clears the screen.
default upnp port
Resets the UPnP Server port to its default value (0x77FF).
exit
Returns to the config level.
no clear counters
Unzeros Query Port counters
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show statistics
Displays statistics and information about the discovery services.
state disable
Disables the Query Port server.
state enable
Enables the Query Port server.
upnp port <number>
Sets the port number the UPnP server will use. <number> = port number.
upnp state disable
Disables the UPnP server.
upnp state enable
Enables the UPnP server.
write
Stores the current configuration in permanent memory.
dns (dns) level commands
clrscrn
Clears the screen.
exit
Exits to the enable level.
lookup <host_or_ip>
Return a lookup on the DNS name or IP address.
show
Show DNS status.
show history
Displays the last 20 commands entered during the current CLI session.
write
Stores the current configuration in permanent memory.
edit 1 (config-profile-basic:default_infrastructure_profile_2) level commands
advanced
Switch to advanced level
apply wlan
Try out WLAN settings without saving them to Flash. If the settings do not work, when you
reboot the device, it will still have the original settings.
clrscrn
Clears the screen.
exit
Exit to the profiles level
network name <text>
Sets the network name.
no network name
Clears the network name.
security
Switch to security level
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
state disable
Disables this profile.
state enable
Enables this profile.
write
Stores the current configuration in permanent memory.
email (config-action-email:wlan0 link state change) level commands
alarm email email <num-
Specifies the email number to send when the alarm turns on.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm