1
Only for models with RJ45 modules
1. HARDWARE OVERVIEW
3. HARDWARE INSTALLATION
The front console port allows a dumb terminal or PC with terminal emulaon soware to
locally access management funcons and connected devices.
The device ports allow simple and exible connecons to serial devices using adapters and
a standard CAT5 cable. Connect one end of the CAT5 cable to the device port and the other
end to an adapter that aaches to the serial console of the target system.
For example, to connect a PC to the console port of the SLC 8000, you only need the RJ45
to DB9F Adapter and a standard CAT5 cable which is supplied with the unit.
The default communicaon parameters for the device ports and console ports are:
9600 baud • 1 stop bit • 8 data bits • No ow control • No parity
Note: SLC 8000 device ports are reversed by default, but are soware congurable.
2. CONNECTING THE SLC 8000
Front View Back View
LCD
Keypad
SD Card
Console
Modem (Oponal)
Dual USB Ports
Device Ports (Modular)
10/100/1000
Dual Network Ports
Power Inlet
(Dual AC or Single AC or Dual DC)
Reversed by Default
1. CTS (In)
2. DSR (In)
3. RX (In)
4. GND
5. GND
6. TX (Out)
7. DTR (Out)
8. RTS (Out)
Indicator LED
Front-mid-rear
Mounng Bracket
1. RTS (Out)
2. DTR (Out)
3. TX (Out)
4. GND
5. GND
6. RX (In)
7. DSR (In)
8. CTS (In)
Console Port (RS-232) Device Ports (RS-232)
!
Thank you for choosing Lantronix. Please register the SLC 8000 Console Manager in order to receive
nocaons for rmware and documentaon updates at www.lantronix.com/product-registraon.
Default Pin Assignments
SLC 8000 Console Manager Quick Start Guide
Accessories Part Number Quanty
For AC Supply Models: AC Power Cord included only 500-041-ACC 1 for Single, 2 for Dual
For DC Supply Models: DC Installaon Kit only 083-152-ACC 1
RJ45 to RJ45, CAT5 Cable, 6.6 (2 m) 200.0062 1
RJ45 to DB9F Adapter* 200.2070A 1
RJ45 Loopback Cable* 500-153 1
START
WHAT’S IN THE BOX
The Lantronix SLC 8000 Advanced Console Manager enables IT professionals to remotely and securely administer servers and networking equipment.
Leveraging the console or emergency management port built into most servers and networking equipment, the SLC 8000 provides remote access
anywhere, anyme. All that is required is an available console, AUX, or serial port on the aached equipment. Using in-band management, you can
manage equipment over the network from virtually any place, using familiar tools like Telnet or Secure Shell (SSH). Out-of-band management
provides access from a local terminal or through an internal modem (P/N 56KINTMODEM-01, sold separately). If a modem is used, dial-in access is
possible in the event that the IP network is unavailable. Once connected, the user has access to the server or IT equipment’s command line interface
(CLI) via the console port to perform maintenance or management tasks. The front LCD panel and keypad allow for quick and easy network
conguraon.
All SLC 8000 models are compable with a variety of equipment, including:
• Switches • Routers • Firewalls • Servers • UPS systems • PBX systems • Telecom switches • PDU
1. Install the unit in a 19-inch rack.
Warning: Do not block the air vents on the sides of the unit. If mounted in an enclosed rack, it is recommended that the rack have a venlaon fan.
2. Connect the equipment to the numbered device ports on the back of the unit using the appropriate cables and adapters.
3. If you installed the internal modem, connect a RJ11 cable between the front panel modem port on the SLC 8000 to your phone line.
4. Connect the unit to the network using the upper network port (Ethernet 1).
5. Connect the power cord and apply power.
6. Wait about a minute and a half for the boot process to complete. When the boot process ends,
the SLC model name and clock appear on the LCD. Detected faults or process messages may also display.
Soware
Reversible
* Only included for models with RJ45 modules
Bay1
Bay2 Bay2
To Next Page
Need help?
General
Weight and Dimensions
