Need help?Do you have a question about the Lantronix SISPM1040 L3 Series and is the answer not in the manual?
Step-by-step guide to configure the switch using a web browser, including PC IP address reconfiguration and connection.
Overview of configuring and managing the switch via the web user interface, covering various functions.
Description of common Web UI navigation controls like Logo, Menu toggle, Save, Help, and Logout.
Displays switch system information, including model, description, location, contact, and serial number.
Configures basic IP settings, IP interfaces, and IP routes, including DHCP and manual IP addressing.
Sets advanced IP settings, IP interfaces, and IP routes, supporting up to 128 interfaces and routes.
Displays the status of the IP protocol layer, including IP interfaces, IPv6 routes, and neighbor cache.
Configures time parameters, supporting manual and automatic NTP time synchronization.
Configures Link Layer Discovery Protocol (LLDP) parameters for interface settings.
Configures LLDP-MED, which enhances LLDP for VoIP devices, providing features like media endpoint discovery.
Provides a status overview for all LLDP neighbors, displaying information about detected LLDP neighbors.
Provides an overview of LLDP-MED neighbors, detailing device types and capabilities.
Provides a status overview for LLDP PoE neighbors, displaying PoE information exchanged.
Provides an overview of EEE information exchanged by LLDP, related to power saving.
Provides an overview of all LLDP traffic, showing global and local counters.
Configures UPnP (Universal Plug and Play) to allow devices to connect seamlessly and simplify network implementation.
Lets you view and set current port parameters, including speed, duplex, and cable type.
Displays an overview of general traffic statistics for all switch ports.
Displays general SFP information and monitoring information, including connector and fiber type.
Lets you configure port power savings features, enabling EEE for low or no traffic utilization.
Configures Aggregation hash mode and the aggregation group, using multiple ports for speed and redundancy.
Sets Link Aggregation Control Protocol (LACP) port parameters to bundle physical ports into a single logical port.
Provides a status overview for all LACP instances, showing aggregation ID, partner system ID, and local ports.
Provides a status overview for LACP status for all ports, indicating LACP enabled and port link status.
Lets you set and view current Link OAM port parameters, supporting Operation Administration and Maintenance.
Displays Link OAM configuration operational status for the selected port.
Lets you view and set current Link OAM Link Event parameters.
Provides detailed OAM traffic statistics for a specific switch port.
Lets you view and set Link OAM Link Event parameters.
Lets you view and set current Loop Protection parameters to detect traffic presence and prevent loops.
Displays the loop protection port status for all ports of the switch.
Lets you view and set current UDLD parameters to detect unidirectional links.
Displays the UDLD status of each port.
Lets you configure DDMI mode and provides an overview of DDMI port parameters.
Displays detailed DDMI information.
Lets you view and set current PoE port settings, and displays the primary power supply output.
Displays the current status for all PoE ports.
Lets you view and set the delay time of power being provided after a device rebooted.
Lets you specify the auto detection parameters to check the link status between PoE ports and PDs.
Lets you define 1-16 profiles for PoE scheduling.
Lets you browse to and select a firmware file to update the PoE firmware controlling the switch.
Lets you set VLAN parameters on the switch, divided into global and per-port sections.
Provides an overview of membership status of VLAN users.
Displays VLAN Port Status for a selected set of VLAN users.
Entries in the VLAN Name Configuration table are shown.
Allows incoming untagged packets to be assigned to a VLAN based on the packet's source MAC address.
Allows adding and deleting MAC-based VLAN Classification List entries and assigning them to different ports.
Supports Ethernet, LLC, and SNAP protocols for VLAN configuration.
Lets you add new Protocol to Group Name mapping entries and view/delete mapped entries.
Allows mapping a Group Name to a VLAN for the switch.
Allows adding, updating, and deleting IP subnet to VLAN ID mapping entries and assigning them to ports.
Lets you configure Stream instances for traffic matching.
Lets you set and view Media Redundancy Protocol parameters.
Lets you set MRP generic settings for all switch ports.
Allows configuration of MVRP global and per-port settings.
Provides Generic Attribute Registration Protocol (GARP) framework for registering attribute values.
Lets you configure GVRP global and port settings.
Monitors and modifies Private VLAN membership configurations.
Enables or disables port isolation on ports in a Private VLAN.
Configures VLAN specifically for voice traffic, allowing QoS-related configuration.
Enables voice traffic forwarding and allows switch to classify and schedule network traffic.
Lets you configure basic QoS Classification settings for all switch ports.
Lets you configure the Policer settings for all switch ports to limit bandwidth of received frames.
Lets you configure the Queue Policer settings for all switch ports.
Provides an overview of QoS Egress Port Shapers for all switch ports.
Configures global and port storm policers for the switch.
Lets you set QoS Egress Port Scheduler parameters for all switch ports.
Displays QoS Egress Port PCP Remarking settings for all switch ports.
Differentiated Services Code Point is a field in the header of IP packets for packet classification purposes.
Lets you configure basic QoS Port DSCP Configuration settings for all switch ports.
Lets you configure the basic QoS DSCP Translation settings for all switches.
Lets you configure the mapping of Queue Priority and DPL to DSCP value.
Lets you configure basic QoS DSCP-based QoS Ingress Classification settings for the switch.
Lets you display the QoS Ingress Map Configuration page.
Lets you display the QoS Egress Map Configuration page.
Shows the QoS Control List (QCL), which is made up of QCEs.
Provides statistics for the different queues for all switch ports.
Provides detailed traffic statistics for a specific switch port.
Allows you to configure the Random Early Detection (RED) settings.
Lets you configure STP system settings which are used by all STP Bridge instances.
Lets you view and set current STP MSTI bridge instance priority parameters.
Provides a status overview of all STP bridge instances.
Provides detailed information on a single STP bridge instance.
Displays the STP port statistics counters of bridge ports in the switch.
Sets timeouts for entries in the dynamic MAC Table and configures the static MAC table.
Displays entries in the MAC Table, sorted by VLAN ID, then by MAC address.
Identifies multicast groups and enables switches to forward packets to the correct devices.
Provides IGMP Snooping related configuration.
Displays the MLD Snooping VLAN Configuration table.
Provides IGMP Snooping status.
Shows entries in the IGMP Group table.
Shows entries in the IGMP SFM Information Table, including SSM information.
Used by IPv6 routers to discover multicast listeners on a directly attached link.
Provides MLD Snooping related configuration.
Displays the MLD Snooping VLAN Configuration table.
Provides MLD Snooping status and statistics.
Shows entries in the MLD Snooping Group Information table.
Shows entries in the MLD SFM Information Table, including SSM information.
Provides MVR related configurations.
Lets you set Media Redundancy Protocol parameters.
Provides statistics for the MVRP protocol for all switch ports.
Shows entries in the MVR Channels (Groups) Information Table.
Shows entries in the MVR SFM Information Table, including SSM information.
Provides IPMC Profile related configurations.
Provides IPMC Profile related configurations.
Configures DHCP Snooping to block intruders on untrusted ports.
Displays dynamic IP assigned information after DHCP Snooping is disabled.
Displays statistics for DHCP snooping.
Configures DHCPv6 (DHCP over IPv6) Snooping to block intruders on untrusted ports.
Forwards DHCP messages between clients and servers not on the same subnet domain.
Configures DHCP Relay agent to insert specific information into DHCP request packets.
Displays statistics for DHCP relay.
Lets you configure DHCPv6 Relay for a specified VLAN.
Shows currently configured relay agents’ status and statistics.
Lets you enable or disable DHCP server per system and per VLAN.
Displays DHCP server status.
Displays an overview of current accounts and allows adding, editing, and deleting users.
Lets you view and set privilege levels on a per group basis.
Lets you configure authentication, authorization, and accounting methods.
Configures access management table, allowing access to the switch based on application type.
Allows you to configure HTTPS settings and maintain the current certificate.
Lets you configure the IEEE 802.1X and MAC-based authentication system and port settings.
Provides an overview of the current 802.1X port states.
Displays detailed 802.1X statistics for a specific switch port.
Provides IP Source Guard related configuration to restrict IP traffic on untrusted ports.
Shows the static IP Source Guard rules.
Shows the dynamic IP Source Guard entries.
Provides IPv6 Source Guard related configuration to restrict IPv6 traffic.
Shows the static IPv6 Source Guard entries.
Provides ARP Inspection related configuration to block attacks by poisoning ARP caches.
Provides ARP Inspection related configuration for VLANs.
Shows the static ARP Inspection rules.
Allows you to configure the Port Security global and per-port settings.
Lets you add and delete static and sticky MAC addresses managed by Port Security.
Shows the MAC addresses secured by the Port Security module.
Lets you view the status for that particular port.
Allows you to configure up to five RADIUS servers.
Provides an overview of the status of the RADIUS servers configured.
Provides detailed statistics for a selected RADIUS server.
Lets you configure up to 5 TACACS+ servers.
Configures the ACL parameters (ACE) of each switch port.
Lets you configure up to 16 ACL rate limiters.
Shows the Access Control List (ACL), which is made up of the ACEs defined on this switch.
Configures an ACE (Access Control Entry) on this page.
Configures SNMPv1 and SNMPv2 on this page.
Configures SNMPv3 community table on this page.
Configures SNMPv3 user table on this page.
Configures up to 12 SNMPv3 views on this page.
Configures up to 12 SNMPv3 accesses on this page.
Configures RMON Statistics on this page.
Provides an overview of RMON Status entries.
Configures RMON History table on this page.
Configures RMON Alarm table on this page.
Configures RMON Event parameters on this page.
Configures CFM Global Configuration parameters.
Configures CFM Domain parameters.
Configures CFM Service parameters.
Configures CFM MEP parameters.
Views CFM MEP Status.
Lets you create and configure an APS Instance.
Shows the current status of APS instances.
Displays ERPS instances and allows configuration.
Shows the current status of the ERPS instances.
Shows detailed status for a specific ERPS instance.
Lets you view and set current Rapid Ring parameters.
Lets you set Media Redundancy Protocol parameters.
Lets you display the Ring Domain Configuration page.
Displays Media Redundancy Protocol status.
Lets you set and view current PTP clock parameters for up to four clock instances.
Defines the port data set as defined in the IEEE 1588 Standard.
Lets you view current PTP clock settings.
Lets you view and set the current PTP clock parameters.
Lets you view 802.1AS Clock Instance Specific Statistics.
Configures SNMP trap parameters.
Lets you configure SMTP (Simple Mail Transfer Protocol).
Configures System Log settings.
Lets you configure the normal modes of digital input/output (DI/DO).
Lets you set and view current trap event severity parameters.
Lets you set router key chain name table parameters.
Lets you set router access-list configuration parameters.
Lets you set common OSPF router global parameters.
Lets you set OSPF area parameters.
Lets you set OSPF router interface parameters.
Lets you set OSPF stub area parameters.
Lets you set OSPF area authentication parameters.
Lets you set OSPF area range parameters.
Lets you set OSPF interface parameters.
Lets you set OSPF virtual link parameters.
Provides various OSPF statuses.
Displays the OSPF router status table.
Displays the OSPF network area status table.
Displays the OSPF IPv4 neighbor status table.
Displays the OSPF interface status table.
Displays the OSPF routing status table.
Displays the OSPF LSA Link State Database table.
Displays the OSPF LSA Router link state database information table.
Displays the OSPF LSA Network link state database information table.
Displays the OSPF LSA Summary link state database information table.
Displays the OSPF LSA ASBR Summary link state database information table.
Displays the OSPF LSA External link state database information table.
Sets OSPFv3 router configuration parameters.
Displays the OSPFv3 router passive interface configuration table.
Displays the OSPFv3 stub area configuration table.
Displays the OSPFv3 area range configuration table.
Displays the OSPFv3 interface configuration table.
Displays the OSPFv3 global status table.
Displays the OSPFv3 network area status table.
Displays the OSPFv3 IPv6 neighbor status table.
Displays the OSPFv3 interface status table.
Displays the OSPFv3 routing status table.
Displays the OSPFv3 LSA General link state database table.
Displays the OSPFv3 LSA Router link state database information table.
Displays the OSPFv3 LSA Network link state database information table.
Displays the OSPFv3 LSA Link link-state database table.
Displays the OSPFv3 IntraArea Prefix Link State Database.
Displays the OSPFv3 LSA Summary link state database information table.
Displays the OSPFv3 LSA ASBR Summary link state database information table.
Displays the OSPFv3 LSA External link state database information table.
Displays the RIP router global configuration table.
Displays the RIP network configuration table.
Displays the RIP neighbor connection table.
Displays the RIP router interface configuration table.
Displays the RIP interface configuration table.
Displays the RIP offset-list configuration table.
Displays the RIP general status information table.
Displays the RIP interface status information table.
Displays the RIP peer table.
Lets you issue ICMP (IPv4) PING packets to troubleshoot IP connectivity issues.
Lets you issue ICMPv6 PING packets to troubleshoot IPv6 connectivity issues.
Lets you perform a traceroute test over IPv4 towards a remote host.
Lets you perform a traceroute test over IPv6 towards a remote host.
Lets you retrieve the local or remote OAM MIB variable data on a particular port.
Used for running the Cable Diagnostics for 10/100 and 1G copper ports.
A feature for switched port analyzer to mirror traffic to a mirror port.
Lets you configure sFlow, including receiver and per-port configurations.
Shows receiver and per-port sFlow statistics.
Provides maintenance configuration functions like save, backup, restore, activate, and delete.
Lets you copy running-config to startup-config for the next reboot.
Allows downloading configuration files from the switch to the web browser.
Lets you upload a file from the web browser to the switch.
Lets you activate configuration files present on the switch.
Lets you delete writable files stored in flash, including startup-config.
Lets you restart the switch.
Lets you reset the configuration of the switch to factory defaults.
Facilitates an update of the firmware controlling the switch.
Provides information about active and alternate firmware images.
Lets you configure DMS mode and monitor device numbers/DMS Controller Switch IP.
Lets you enable/disable DMS mode and specify DMS Controller Priority.
Requires a valid API key and Google Cloud Platform billing account for Google Maps.
Provides an overview of the devices list.
Displays devices in a graphic networking topology view.
Displays the graphical image created at DMS > Maintenance > Floor Image.
Helps find device locations by placing icons on Google Maps.
Lets you upload and manage floor map images.
Lets you run a diagnostic test on a selected device.
Displays a visual chart of network traffic of all devices.
Lets you assign a static IP address from a DHCP pool to a switch port.
Details how to configure DHCP Per Port via the Web UI.
Describes MRP operation, its components, and port status types.
Describes normal and failure modes of MRP operation.
Explains ERPS (Ethernet Ring Protection Switching) protocol and its benefits.
Explains basic concepts supporting ERPS Ring, like RPL, owner node, neighbor node, and messages.
Lists sample IP addresses used in ERPS configurations.
Provides sample configurations for Major and Sub Rings.
To Next Page
General