lap 172PG - User Manual

To Next Page

Instruction leaflet

Half Lantern PIR

Outdoor Wall Light

19/07/2021

172PG, 430PG

• Fitting/Replacing the bulbs - MAX 15W LED E27 GLS.

• When changing a bulb, always, switch off at the

mains and allow the bulb to cool before handling.

Dispose of used bulbs carefully. Do not exceed the

wattage stated or use a different shape bulb from

that indicated on the fitting.

• Do not exceed the wattage stated or use a different

shape bulb from the indicated on the fitting.

• Unscrew the bulb anti clockwise to remove.

• Carefully locate the bulb in the lampholder and turn

clockwise to secure.

Fitting/replacing bulbs

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.

Check with your Local Authority or retailer for recycling advice. The packaging on this product can also be recycled.

Recycling advice

Safety information

We recommend cleaning with a soft dry cloth.

Do not use solvents or abrasive cleaners as these could

damage the finish.

Glass parts – Wipe clean with a damp cloth. Do not use

abrasive materials as these will damage the finish.

Cleaning

For your safety, always switch off the supply before changing lightbulbs, or cleaning.

The glass shade must be replaced if it becomes cracked or damaged.

Do not use product without glass shade attached.

Replace Cracked

Shade

UK Manufacturer:

Kingfisher International Products Limited,

3 Sheldon Square, London, W2 6PX,

United Kingdom.

EU Manufacturer:

Kingfisher International Products B.V.

Rapenburgerstraat 175E,

1011 VM Amsterdam, The Netherlands.

The unit must be installed in a vertical position, and fitted

1-2m above the ground. The PIR sensor can be adjusted

using the SENS and TIME dials.

The detection angle is set at 105 degrees. The maximum

detection distance is 8m.

The length of time that the light is on can be adjusted

by turning the ‘Time’ dial, which can be altered between

8 seconds to 9 minutes duration. See (1) below.

Adjust the light level that the lamp switches on by

adjusting the 'LUX' screw (2).

PIR Adjustment

Max. 8M

1-2M

1.7M

Need help?

Do you have a question about the lap 172PG and is the answer not in the manual?

This document describes the Half Lantern PIR Outdoor Wall Light, models 172PG and 430PG, which is a motion-sensing outdoor wall light designed for illumination and security.

Function Description:

The Half Lantern PIR Outdoor Wall Light is a wall-mounted luminaire equipped with a Passive Infrared (PIR) sensor. This sensor detects motion within its detection zone, automatically switching on the light. The unit is designed for outdoor use, providing illumination for pathways, entrances, or other areas around a property. The PIR sensor's sensitivity and the duration the light stays on after detection are adjustable, allowing users to customize its operation to their specific needs. The light also features an adjustable LUX setting, which determines the ambient light level at which the lamp will activate, preventing it from turning on during daylight hours.

Important Technical Specifications:

Voltage: 240V 50Hz
Lamp Type: Max. 1 x 15W LED E27 GLS (General Lighting Service) bulb. It is crucial not to exceed the stated wattage or use a different bulb shape.
PIR Detection Angle: 105 degrees
Maximum PIR Detection Distance: 8 meters
PIR Mounting Height: The unit must be installed in a vertical position, 1-2 meters above the ground for optimal PIR sensor performance.
Time Adjustment (Light ON Duration): Adjustable from 8 seconds to 9 minutes.
LUX Adjustment (Ambient Light Level): Adjustable from approximately 2 lux (dark) to 2000 lux (daylight).
IP Rating: IP44, indicating protection against solid objects larger than 1mm and splashes of water from any direction. This makes it suitable for outdoor environments.
Electrical Classification: Double Insulated, meaning it does not require an Earth connection.
Mains Supply Cable: Must have a minimum cross-sectional area of 1.0mm².

Usage Features:

PIR Sensor Adjustment: The unit includes two dials for adjusting the PIR sensor:
- TIME Dial (1): Controls the length of time the light remains on after motion detection. It can be set from 8 seconds to 9 minutes.
- LUX Screw (2): Adjusts the ambient light level at which the lamp will switch on. Turning it towards the '+' symbol (2000 lux) will make the light activate in brighter conditions, while turning it towards the '-' symbol (2 lux) will make it activate only in darker conditions.
Bulb Replacement: Uses a standard E27 GLS bulb, with a maximum wattage of 15W LED. Bulbs are secured by turning clockwise into the lampholder and removed by turning anti-clockwise.
Installation: The unit is designed for wall mounting. It requires careful planning of cable layout to avoid hazards and ensure cables are protected. It is recommended to use suitable conduit or plastic trunking for cables in walls. The product should be installed by a competent and qualified electrician in accordance with IEE Wiring regulations and current Building Regulations.
Wiring: The product features a connection block for wiring. The neutral (N) wire connects to the blue terminal, and the switched live (L) wire connects to the brown terminal. As it is double insulated, no earth connection is required.
Safety Precautions: Always switch off the mains supply before installing, maintaining, or changing bulbs. Allow bulbs to cool before handling. Do not exceed the specified wattage or use incorrect bulb types. The entire unit can become hot during operation.

Maintenance Features:

Cleaning: The unit should be cleaned with a soft, dry cloth. For glass parts, a damp cloth can be used. Solvents or abrasive cleaners should not be used as they can damage the finish.
Glass Shade Replacement: If the glass shade becomes cracked or damaged, it must be replaced. The product should not be used without the glass shade attached.
Bulb Disposal: Used bulbs should be disposed of carefully and responsibly.
Recycling: Waste electrical products should not be disposed of with household waste. Users are advised to recycle where facilities exist and to check with their local authority or retailer for recycling advice. The product packaging is also recyclable.
Pre-installation Check: Before installation, ensure the wall is capable of holding the product's weight and avoid damaging any concealed wiring or pipes.

lap 172PG Specifications

General

Brand	lap
Model	172PG
Category	Outdoor Light
Language	English

Related product manuals

lap 2617S-PIR

7 pages