To Next PageTo Next Page
Need help?Do you have a question about the Laserworld CS-2000RGB and is the answer not in the manual?
General| Brand | Laserworld |
|---|---|
| Model | CS-2000RGB |
| Category | Lighting Equipment |
| Language | English |
Use the device strictly according to the operating instructions.
Do not operate if the device shows visible damage to its housing or components.
Avoid direct eye exposure to the laser light source; it can cause blindness.
Avoid operating the device in humid, wet, or dusty conditions.
Prevent water ingress and avoid placing liquid containers near the device.
Verify and use the correct voltage as specified in the manual and on the device.
Ensure the device is disconnected from mains power during installation.
Installation must be performed by qualified personnel following local safety regulations.
Ensure maximum permissible exposure (MPE) levels are not exceeded in public or staff areas.
Some countries may require an additional inspection by technical control institutes.
Connect an easily accessible interlock or circuit breaker to the projector for safety.
Ensure the power supply connection is easily accessible.
Mount the laser with at least 15 cm clearance from walls and objects.
Use a safety cord rated for tenfold the device's weight for secure wall/ceiling mounting, following safety regulations.
Avoid immediate operation after significant temperature changes due to condensation risk.
Avoid dimmers and electronically switched sockets; do not share mains with large appliances.
Ensure adequate ventilation and avoid placing the device on warm surfaces or covering openings.
Prevent overheating by avoiding direct exposure to spotlights and ensuring proper placement.
Only qualified engineers should maintain or service this product; it has no user-serviceable parts.
Always disconnect the mains plug before installing, opening, or cleaning the device.
Remove reflective items like rings and watches before working on the projector.
Use only non-reflecting tools when working on the device.
Wear appropriate protective clothing, including goggles and gloves, based on laser specifications.
Moisture and heat reduce laser system lifetime and void warranty.
Frequent on/off cycling significantly reduces laser diode durability.
Protect the device from shocks and ensure proper protection during transport.
Always ensure adequate ventilation for the laser device.
Avoid directing spotlights, especially moving heads, towards the device.
Monitor temperature after approximately 30 minutes of operation during new installations.
Relocate the projector to a cooler area if overheating occurs.
Keep the device dry and protected from moisture, rain, and dampness.
Turn off the device when not in use to prevent diode wear, even without visible output.
Periodically clean dust from fans and laser area; overheating voids warranty.
Clean fog fluid residue and reposition the fog machine if present.
Ecoline, Evolution, Club, Proline series are not for professional use; allow 15 min cool-down after 1 hour.
Consult the FAQ on www.laserworld.com for troubleshooting assistance.
Tampering with warranty labels or improper handling voids the warranty.
Warning: Avoid exposure to laser beam due to radiation hazard.
Caution: Radiation risk present if the device cover is removed.
This device is intended for use only in enclosed spaces.
Controls for power activation and key switch operation.
Adjustments for sound sensitivity and mode selection.
Ports for DMX control and ILDA signal input/output.
Connectors for power supply and power output.
Fans for cooling and LED indicators for status.
Port for safety interlock connection.
Device operates automatically in a pre-programmed sequence.
Device reacts to sound, with sensitivity adjusted by a rear trim pot.
Device operates via DMX controller when switch 10 is off.
Set DMX address using DIP switches 1-9, each representing a binary value.
The laser uses 13 DMX channels; ensure no address overlap with other devices.
Controls laser mode: Off, sound, automatic, or DMX.
Selects from various pre-programmed patterns.
Controls the strobe effect functionality.
Manages the horizontal scanning movement of the laser beam.
Controls vertical beam movement and zoom effects.
Adjusts the width of the laser beam (rotation over Y-axis).
Manages rotation of the laser beam (rotation over Y-axis).
Controls the height of the laser beam (rotation over X-axis).
Sets rotation speed and direction (clockwise/counter-clockwise).
Controls beam blanking for effects like points or lines.
Activates wave-like patterns for the laser beam.
Selects colors, including white, rainbow static, and moving effects.
Determines the format of displayed images.
Connect the device via ILDA cable to an interface/controller with laser software.
Switch off the device, turn the key to 'OFF', and disconnect the power cable.
Details on DPSS and diode laser sources and their classification.
Information on scanner type and scanning angle capabilities.
Supported operating modes and beam properties.
Specifications for power requirements and energy usage.
Details on operational temperature range and physical dimensions.
Specifications for the weight of the devices.
Red, Green, and Blue laser output power for CS-1000RGB models.
Red, Green, and Blue laser output power for CS-2000RGB models.
Red, Green, and Blue laser output power for CS-4000RGB models.
