Laski F-360 SW User Manual

40 pages

Questions and Answers:

P
powellgregoryAug 4, 2025
Why won't my Laski F-360 SW Cutter engine start?
- R
  robin56Aug 4, 2025
  If your Laski Cutter's engine won't start, several factors could be the cause. First, check that the speed regulator lever is not in the STOP position; if it is, set the proper speed. Ensure the ignition breaker is in the "I" position, not "0". Inspect the wiring for any broken leads. Also, check the spark plug; it may need cleaning or replacing. A fouled fuel filter can prevent starting, so change the filter element. Confirm that there is enough fuel and that the engine oil level is sufficient; top up if necessary.
R
Richard ShafferAug 11, 2025
What to do if the Laski F-360 SW Cutter has insufficient engine power?
- A
  Ashley HodgesAug 11, 2025
  If your Laski Cutter has insufficient engine power, the air filter might be fouled and needs cleaning. Another potential cause is dead piston rings, which would require repair.
D
Darrell GarciaAug 19, 2025
What causes insufficient cutting head power in a Laski F-360 SW?
- C
  Carlos KleinAug 20, 2025
  Insufficient cutting head power in your Laski Cutter can stem from a few issues. Check the blades for damage and replace them if needed. Also, inspect the blades for bluntness or wear; replace or regrind them as necessary. Finally, the wire control might be out of tune and require adjustment.

Laski F-360 SW Specifications

General

Brand	Laski
Model	F-360 SW
Category	Cutter
Language	English

Summary

Foreword

EC Conformity Declaration

Product Identification

Work Safety Instructions

Safe Operation Guidelines

Covers intended use, prohibited uses, and general safety rules for operators.

Work Safety Symbols

General Safety Pictograms

Explains symbols for reading manual, PPE, and machine setup.

Maintenance Safety Pictograms

Covers symbols for powering off and using supports during maintenance.

Hazard Warning Pictograms

Specific Hazard Alerts

Alerts users to critical hazards like flammable liquids, hot parts, and rotating machinery.

Operational Risk Warnings

Warns of specific risks like lower limb injury, crushing, and cutting head operation.

Transport and Setup Safety

Indicates lashing points and closing guards before starting.

Transport and Handling

Safe Lifting Procedures

Provides instructions on safe lifting using designated points and caution against unstable parts.

Unloading from Transport Pallet

Design Safety Features

Dead-Man Lever Function

Explains the function and necessity of the dead-man lever for safe operation.

Attendant's Place

Controls

Noise and Vibrations

Operation Preparation

Before Operation Checks

Lists essential checks to perform before the initial operation of the machine.

Putting into Operation

Transport, Handling and Storage

Storage Guidelines

Provides guidance on storing the machine to protect it from weather effects.

Stump Cutting Operation

Stump Positioning and Setup

Details positioning the cutter relative to the stump for effective cutting.

Cutting Technique

Explains the process of starting the cut and adjusting speed during operation.

Chip Clearing and Safety

Cutting Recommendations

Offers recommendations for optimal cutting pressure and engine speed.

Putting out of Operation

Emergency Situations

Immediate Shutdown Procedures

Lists conditions requiring immediate shutdown and appropriate actions.

Fire Safety

Specifies the type of extinguisher to use for fires and when to call the fire brigade.

Technical Description

Maintenance

Servicing Safety and Prerequisites

Outlines safety rules and requirements for performing maintenance tasks.

Routine Maintenance Checks

Details essential checks for V-belts, lubrication, control cables, and general condition.

Waste Disposal and Material Handling

Instructs on proper disposal of used oil, filter elements, and handling hazardous materials.

Workshop Safety and Handling

Engine Oil Change Schedule

Details the procedure and schedule for changing the engine oil.

Air Filter Maintenance

Ignition System Checks

Covers checks for the ignition system, spark plug, and power cable.

Engine Cleaning and Starting

Provides instructions for cleaning the engine and describes the starting equipment.

Electrical and Brake System Checks

Chassis Upkeep

Recommends regular checks of chassis joints, wear, tire pressure, and cleaning.

Replacement of Blades and Regrinding

V-belt Tension Adjustment

Belt Tension and Alignment

Describes checking belt tension, alignment, and using a straight-edge rule for accuracy.

Engine Mounting and Belt Adjustment

Failures and Troubleshooting

Engine Start Issues

Lists causes and remedies for the engine failing to start.

Engine Power Issues

Outlines potential causes and solutions for reduced engine power.

Cutting Head Power Issues

Waste Disposal

Warranty

Service Report