LAVAZZA Espresso Point Matinee 120V

Questions and Answers

B
Brandon ThompsonSep 9, 2025
Why is the cup compartment light off on my LAVAZZA Espresso Point Matinee 120V?
- M
  michael21Sep 9, 2025
  If the cup compartment light on your LAVAZZA Coffee Maker doesn't turn on, check the following: * The bulb may be burnt out. Replace the bulb. * There may be mechanical disconnections in the harness. Inspect the harness and connections to the light-holder and electronic card, making any necessary corrections. * The electronic card may be defective. Replace the electronic card.
M
Molly HuntAug 23, 2025
What to do if LAVAZZA Coffee Maker delivers burnt coffee?
- S
  Stacy OrtegaAug 23, 2025
  If your LAVAZZA Coffee Maker delivers burnt coffee and the feed pilot light flashes, the 100 °C thermostat is likely faulty, and the safety thermostat has activated. Replace the thermostat.
A
alyssa41Aug 25, 2025
What to do if LAVAZZA Coffee Maker is leaking water inside?
- T
  Tanner HicksAug 26, 2025
  If your LAVAZZA Coffee Maker is leaking water inside, here's what to check: * **Leakage between the FAP press and chamber:** Replace the perforated membrane after dismantling the output unit. * **Leakage between the chamber and the integral teflon coated plate:** Dismantle the output unit, remove scale, and replace the membrane. * **Leakage between the integral teflon coated plate and the stainless steel labyrinth:** Dismantle the output unit and fit new seals. * **Leakage on the connection between the teflon pipe and unit:** Check and tighten the Teflon pipe nut. Replace the Teflon pipe if necessary, along with any damaged union elbow.
C
Christine LunaAug 27, 2025
Why is my LAVAZZA Coffee Maker pump buzzing but not delivering coffee?
- L
  Laurie FoxAug 27, 2025
  If your LAVAZZA Coffee Maker pump buzzes but doesn't deliver coffee, and the green light flashes, it could be due to: * A faulty solenoid valve preventing water passage. Replace the solenoid valve. * Air in the hydraulic circuit. Check the connection between the hydraulic circuit and the suction system. * A defective electronic card. Replace the card.
F
fwrightAug 28, 2025
What to do if LAVAZZA Coffee Maker delivers cold coffee?
- A
  Amanda BowmanAug 28, 2025
  If your LAVAZZA Coffee Maker is delivering cold coffee, the issue might be: * The ceramic cup is too cold. Preheat the cup before use by placing it in a warm area or on top of the machine. * The 100 °C thermostat is damaged. Replace the thermostat.
R
Rebecca GonzalezAug 29, 2025
Why is the low water light blinking on my LAVAZZA Espresso Point Matinee 120V when the tank is full?
- A
  amandagonzalezAug 29, 2025
  If the low water light blinks on your LAVAZZA Coffee Maker even when the tank is full, check these: * Ensure the tank is properly connected. * The electronic card of the machine may be damaged and require replacement. * Inspect the connectors in the electronic card and harness for disconnections. If the float contact is faulty, replace it.
S
Sean VargasSep 18, 2025
Why does the function LED not flash on my LAVAZZA Coffee Maker?
- B
  Benjamin CalhounSep 18, 2025
  If the LED for the activated function fails to flash on your LAVAZZA Coffee Maker, it could be due to: * The electronic card not functioning correctly. Replace the electronic card. * The rotor of the volumetric dosing device not functioning. Dismantle the device and ensure there are no obstructions. If cleaning doesn't help, replace it. * Mechanical disconnections in the measuring device wiring. Check the connections.
M
matthewchavezSep 19, 2025
Why isn't the kickback element working on my LAVAZZA Espresso Point Matinee 120V Coffee Maker?
- E
  Erica SantanaSep 22, 2025
  If the kickback element on your LAVAZZA Coffee Maker isn't working, the kickback element is defective and needs to be replaced.
C
Christopher MillerSep 7, 2025
Why does hot water come out of the coffee spout when requesting hot water on my LAVAZZA Espresso Point Matinee 120V?
- S
  Shannon McguireSep 8, 2025
  If hot water comes out of the coffee spout when you request hot water on your LAVAZZA Coffee Maker, it could be: * The two-way solenoid valve is blocked or defective. Check for grains inside the valve body; if the issue persists, replace the valve. * The steam jet is clogged. Clean the jet.
B
Brooke LewisSep 4, 2025
What to do if pod is hard to insert into LAVAZZA Espresso Point Matinee 120V Coffee Maker?
- P
  Patrick MccannSep 5, 2025
  If the pod is hard to insert into your LAVAZZA Coffee Maker, consider the following: * The pod drawer might be full. Extract and empty the drawer, removing any excess used pods. * The FAP press may be lowered, the solenoid valve might fail to discharge, or the stainless steel spring in the chamber could be broken. Replace the faulty solenoid valve and/or the spring. * The jaws could be blocked by coffee powder. Dismantle the output unit and clean the jaws slide base. * The discharge pipe might be choked. Check the pipe condition and replace it if necessary.

Summary

General Information

1.1 Introduction to Manual

Manual's content overview: safety, problem-solving, wiring diagrams.

1.2 Safety Information

Critical safety guidelines, warnings, and potential hazards for operation and maintenance.

1.3 Safety Specifications

Essential safety prescriptions for correct machine operations and maintenance interventions.

1.4 Residual Risks Analysis

Risk analysis for machine use and maintenance, emphasizing adherence to instructions.

1.5 Environmental Conditions

Specifies allowed environmental operating conditions, temperature, and humidity limits.

1.6 Warehousing Procedures

Guidelines for storing the machine, protecting it from dust and atmospheric agents.

1.7 Scrapping and Disposal

Procedures for machine disposal according to legislation and component segregation.

1.8 Transport Guidelines

Instructions for careful charge, discharge, and moving operations using original packing.

1.9 Tools for Maintenance

Lists the essential tools required for performing maintenance tasks on the Espresso Point machine.

1.10 Maintenance Accessories

Details optional accessories that facilitate and improve maintenance procedures.

Technical Information

2.1 Wiring Diagram Components List

Component references, codes, and denominations for the machine's electrical wiring.

2.1 Wiring Diagram Schematic

Detailed schematic illustrating the electrical connections and layout of the machine's components.

Maintenance Procedures

3.A Front Part Preliminary Maintenance

Step-by-step guide for initial maintenance tasks on the front part of the machine.

3.B Rear Part Preliminary Maintenance

Step-by-step guide for initial maintenance tasks on the rear part of the machine.

3.1 Delivery Unit and Chamber Maintenance

Detailed steps for maintaining the delivery unit and the chamber, including component removal.

3.1 Labyrinth Seal Replacement

Instructions for cleaning and substituting the seal in the delivery unit's labyrinth.

3.1 Solenoid Valve and FAP-Press Isolation

Procedures to isolate the solenoid valve and FAP-press cover for maintenance.

3.1 Chamber Dismantling and Reassembly

Steps for dismantling and reassembling the chamber, including membrane replacement.

3.2 Jaws Maintenance Procedure

Procedure for maintaining the jaws, including lifting the heating unit and extracting the base.

3.3 Steam Jet Maintenance

Instructions for manually undoing the knob and removing the steam nozzle.

3.4 Light Holder Replacement

Steps to unscrew the transparent cap, replace the bulb, and remove the light-holder.

3.5 Volumetric Dosing Device Extraction

Procedure for extracting the volumetric dosing device and its connection pipe.

3.6 Pump Support Brace Removal

Steps to loosen pump support braces and disconnect pump feed cables.

3.6 Pump Extraction and Seal Replacement

Instructions for extracting the pump, unscrewing fittings, and replacing the seal.

3.7 Solenoid Valve Cable Extraction

Procedure to extract power and earth cables from the solenoid valve.

3.8 Electronic Card Cover Removal

Steps to remove the electronic card cover and extract rear cables for switch or plug replacement.

Troubleshooting and Faults

Fault: Machine Not Starting

Troubleshooting steps for when machine lights are off and the machine fails to start.

Fault: Low Water Warning Blinking

Diagnosing and resolving issues when the low water warning light blinks with a full tank.

Fault: Cup Compartment Light Off

Troubleshooting steps for when the cup compartment light fails to illuminate.

Fault: Feed Pilot Light Off

Steps to resolve the issue where the feed pilot light is off during machine operation.

Fault: Feed Pilot Light Blinking

Diagnosing and fixing problems when the feed pilot light blinks erratically.

Fault: Indicators Remain Off After Heating

Troubleshooting steps for when switchboard indicators stay off after the machine has heated.

Fault: Delivery Function LED Failure

Resolving issues where the delivery function is activated but the corresponding LED fails to flash.

Fault: Machine Fails to Start

Troubleshooting steps for when the machine fails to start after inserting the pod.

Fault: Pump Start Failure & LED Off

Diagnosing pump failure and non-flashing LED when the machine should start.

Fault: Pump Buzzing & No Coffee

Resolving issues where the pump buzzes, but no coffee is delivered.

Fault: Clogged Unit, No Beverage

Troubleshooting steps for a clogged unit where the pump stops and no beverage is produced.

Fault: Water from Steam Jet Outlet

Diagnosing and fixing water emerging from the steam jet outlet instead of the coffee spout.

Fault: Cold Coffee Issue

Troubleshooting steps when the coffee is cold, checking cup temperature and thermostat.

Fault: Burnt Coffee & Flashing Pilot Light

Resolving issues where coffee is burnt and the feed pilot light flashes.

Fault: Burnt Coffee & Pilot Light Off

Troubleshooting steps for burnt coffee and the feed pilot light not flashing.

Fault: Pod Entry Difficulty

Diagnosing problems with pod drawer fullness or blocked pods causing entry difficulty.

Fault: Water Leakage - Solenoid Valve

Identifying and fixing water leakage points related to the solenoid valve within the structure.

Fault: Water Leakage - Steam Jet;Electronic Card

Troubleshooting steam delivery issues and water leaks related to electronic card or clogged jets.

Fault: Water Leakage - Nipple;Connections

Identifying and fixing water leakage points on solenoid valve nipples and teflon pipe connections.

Fault: Water Leakage - Pump;Seals

Troubleshooting water leakage on the pump, including nut tightening, O-ring seals, and pipe fitting.

Fault: Kickback Element Failure

Resolving issues where the kickback element fails to indicate the approach of deliveries.