LAVAZZA Espresso Point Matinee 120V User Manual (English)

Questions and Answers:

H
Hayley WalterSep 6, 2025
What to do if LAVAZZA Coffee Maker is not starting after inserting the pod?
- F
  francesbryantSep 6, 2025
  If your LAVAZZA Coffee Maker fails to start after inserting a pod, and there's no noise, the pump doesn't start, and the green LED doesn't flash, check: * The microswitch may be defective. Replace it. * The button on the electronic keyboard or its flat cable might not work. Replace the electronic keyboard. * The mechanical connections on the harness could be incorrect, or the pump cables might be inverted. Examine and, if worn, replace the harness. Check the correct insertion of the fastons and terminals, and invert the pump connections. * The electronic card may be defective. Replace the card. * The pump might be defective and not starting. Replace the pump.
C
Christopher MillerSep 7, 2025
Why does hot water come out of the coffee spout when requesting hot water on my LAVAZZA Espresso Point Matinee 120V?
- S
  Shannon McguireSep 8, 2025
  If hot water comes out of the coffee spout when you request hot water on your LAVAZZA Coffee Maker, it could be: * The two-way solenoid valve is blocked or defective. Check for grains inside the valve body; if the issue persists, replace the valve. * The steam jet is clogged. Clean the jet.
B
Brandon ThompsonSep 9, 2025
Why is the cup compartment light off on my LAVAZZA Espresso Point Matinee 120V?
- M
  michael21Sep 9, 2025
  If the cup compartment light on your LAVAZZA Coffee Maker doesn't turn on, check the following: * The bulb may be burnt out. Replace the bulb. * There may be mechanical disconnections in the harness. Inspect the harness and connections to the light-holder and electronic card, making any necessary corrections. * The electronic card may be defective. Replace the electronic card.

LAVAZZA Espresso Point Matinee 120V Specifications

General

Brand	LAVAZZA
Model	Espresso Point Matinee 120V
Category	Coffee Maker
Language	English

Summary

General Information

1.1 Introduction to Manual

Manual's content overview: safety, problem-solving, wiring diagrams.

1.2 Safety Information

Critical safety guidelines, warnings, and potential hazards for operation and maintenance.

1.3 Safety Specifications

Essential safety prescriptions for correct machine operations and maintenance interventions.

1.4 Residual Risks Analysis

Risk analysis for machine use and maintenance, emphasizing adherence to instructions.

1.5 Environmental Conditions

Specifies allowed environmental operating conditions, temperature, and humidity limits.

1.6 Warehousing Procedures

Guidelines for storing the machine, protecting it from dust and atmospheric agents.

1.7 Scrapping and Disposal

Procedures for machine disposal according to legislation and component segregation.

1.8 Transport Guidelines

Instructions for careful charge, discharge, and moving operations using original packing.

1.9 Tools for Maintenance

Lists the essential tools required for performing maintenance tasks on the Espresso Point machine.

1.10 Maintenance Accessories

Details optional accessories that facilitate and improve maintenance procedures.

Technical Information

2.1 Wiring Diagram Components List

Component references, codes, and denominations for the machine's electrical wiring.

2.1 Wiring Diagram Schematic

Detailed schematic illustrating the electrical connections and layout of the machine's components.

Maintenance Procedures

3.A Front Part Preliminary Maintenance

Step-by-step guide for initial maintenance tasks on the front part of the machine.

3.B Rear Part Preliminary Maintenance

Step-by-step guide for initial maintenance tasks on the rear part of the machine.

3.1 Delivery Unit and Chamber Maintenance

Detailed steps for maintaining the delivery unit and the chamber, including component removal.

3.1 Labyrinth Seal Replacement

Instructions for cleaning and substituting the seal in the delivery unit's labyrinth.

3.1 Solenoid Valve and FAP-Press Isolation

Procedures to isolate the solenoid valve and FAP-press cover for maintenance.

3.1 Chamber Dismantling and Reassembly

Steps for dismantling and reassembling the chamber, including membrane replacement.

3.2 Jaws Maintenance Procedure

Procedure for maintaining the jaws, including lifting the heating unit and extracting the base.

3.3 Steam Jet Maintenance

Instructions for manually undoing the knob and removing the steam nozzle.

3.4 Light Holder Replacement

Steps to unscrew the transparent cap, replace the bulb, and remove the light-holder.

3.5 Volumetric Dosing Device Extraction

Procedure for extracting the volumetric dosing device and its connection pipe.

3.6 Pump Support Brace Removal

Steps to loosen pump support braces and disconnect pump feed cables.

3.6 Pump Extraction and Seal Replacement

Instructions for extracting the pump, unscrewing fittings, and replacing the seal.

3.7 Solenoid Valve Cable Extraction

Procedure to extract power and earth cables from the solenoid valve.

3.8 Electronic Card Cover Removal

Steps to remove the electronic card cover and extract rear cables for switch or plug replacement.

Troubleshooting and Faults

Fault: Machine Not Starting

Troubleshooting steps for when machine lights are off and the machine fails to start.

Fault: Low Water Warning Blinking

Diagnosing and resolving issues when the low water warning light blinks with a full tank.

Fault: Cup Compartment Light Off

Troubleshooting steps for when the cup compartment light fails to illuminate.

Fault: Feed Pilot Light Off

Steps to resolve the issue where the feed pilot light is off during machine operation.

Fault: Feed Pilot Light Blinking

Diagnosing and fixing problems when the feed pilot light blinks erratically.

Fault: Indicators Remain Off After Heating

Troubleshooting steps for when switchboard indicators stay off after the machine has heated.

Fault: Delivery Function LED Failure

Resolving issues where the delivery function is activated but the corresponding LED fails to flash.

Fault: Machine Fails to Start

Troubleshooting steps for when the machine fails to start after inserting the pod.

Fault: Pump Start Failure & LED Off

Diagnosing pump failure and non-flashing LED when the machine should start.

Fault: Pump Buzzing & No Coffee

Resolving issues where the pump buzzes, but no coffee is delivered.

Fault: Clogged Unit, No Beverage

Troubleshooting steps for a clogged unit where the pump stops and no beverage is produced.

Fault: Water from Steam Jet Outlet

Diagnosing and fixing water emerging from the steam jet outlet instead of the coffee spout.

Fault: Cold Coffee Issue

Troubleshooting steps when the coffee is cold, checking cup temperature and thermostat.

Fault: Burnt Coffee & Flashing Pilot Light

Resolving issues where coffee is burnt and the feed pilot light flashes.

Fault: Burnt Coffee & Pilot Light Off

Troubleshooting steps for burnt coffee and the feed pilot light not flashing.

Fault: Pod Entry Difficulty

Diagnosing problems with pod drawer fullness or blocked pods causing entry difficulty.

Fault: Water Leakage - Solenoid Valve

Identifying and fixing water leakage points related to the solenoid valve within the structure.

Fault: Water Leakage - Steam Jet/Electronic Card

Troubleshooting steam delivery issues and water leaks related to electronic card or clogged jets.

Fault: Water Leakage - Nipple/Connections

Identifying and fixing water leakage points on solenoid valve nipples and teflon pipe connections.

Fault: Water Leakage - Pump/Seals

Troubleshooting water leakage on the pump, including nut tightening, O-ring seals, and pipe fitting.

Fault: Kickback Element Failure

Resolving issues where the kickback element fails to indicate the approach of deliveries.

Related product manuals

LAVAZZA ESPRESSO POINT MATINEE

43 pages

LAVAZZA ESPRESSO MAXI POINT

6 pages

LAVAZZA Espresso Point EP2302

55 pages

LAVAZZA Espresso & Cappuccino

LAVAZZA EP MAXI 1050 DUAL

104 pages

LAVAZZA ELM 7000 Amodo Mio

80 pages

LAVAZZA LM 840 Tiny Eco Rosa

100 pages

LAVAZZA EP 1800 LAVAZZA TIME

84 pages

LAVAZZA Espresso Point Matinee 120V User Manual

Table of Contents