J
Joseph RojasSep 6, 2025
What causes water in the oil of Lavor Washer?
- BBenjamin HopkinsSep 6, 2025
If there is water in the oil of your Lavor Washer, it is likely due to worn-out O-rings (water and oil). Contact an authorized service center.
To Next PageTo Next PageWhat causes water in the oil of Lavor Washer?
If there is water in the oil of your Lavor Washer, it is likely due to worn-out O-rings (water and oil). Contact an authorized service center.
Why Lavor MISSISSIPPI R pump doesn’t reach necessary pressure?
If the pump on your Lavor Washer isn't reaching the necessary pressure, consider the following: * Insufficient flow. Check that the delivery rate is 30% higher than the value stated on the appliance’s technical data plate. * A clogged water inlet filter. Remove and clean the filter. * Pressure regulator valve set on minimum. Increase the pressure by screwing in the pressure regulator knob. * The nozzle is worn out. Replace the nozzle. For issues like clogged or worn-out suction/delivery valves, contact an authorized service center.
How to fix Lavor Pressure Washer that does not start?
If your Lavor Pressure Washer doesn't start when you turn on the main switch, make sure the plug is properly connected and the electric cable is in good condition. Also, check the connection panel fuses and replace them if they are burnt out.
What to do if the boiler of Lavor Pressure Washer doesn't start?
If the boiler of your Lavor Pressure Washer doesn't start when you turn on the burner switch: * Check the fuel level in the tank and ensure the rigid suction pipe is clean. * Replace the line filter. * Replace the fuel pump if it's blocked or burnt out. * Replace the thermostat if it is damaged. * Check the positioning of the electrodes. * Replace the fuse if it is burnt out.
What to do if my Lavor MISSISSIPPI R Washer won't start?
If your Lavor Washer isn't starting, there could be several reasons: * The plug may not be properly inserted. Ensure it's correctly fitted in the power socket. * The electric socket might be faulty. Have it checked by a professional. * The main voltage could be insufficient. Verify the suitability of your mains system. * The pump might be stuck. Try turning the switch to ON while pressing the nozzle trigger. If it persists, seek assistance from an authorized service center. * The extension lead might not be sufficient. Refer to the maintenance section for guidance.
What to do if pressure fluctuates when lance is on Lavor Pressure Washer?
If the pressure values of your Lavor Pressure Washer decrease and increase when the lance is turned on: * Clean or replace the nozzle. * Descale the boiler coil or lance.
What causes irregular pressure fluctuations in Lavor Pressure Washer?
If you notice irregular pressure fluctuations in your Lavor Pressure Washer: * Check and/or replace the suction and/or delivery valves. * Check and clean the foreign matters in the valves. * Check the suction pipe. * Check and/or replace the seals.
How to reduce noisiness in Lavor Pressure Washer?
If your Lavor Pressure Washer is excessively noisy: * Check the suction pipes. * Replace the valve springs. * Check and clean the suction and delivery valves. * Replace the bearings. * Reduce the liquid temperature.
What to do if the Lavor Washer boiler doesn't start?
If the boiler of your Lavor Washer doesn't start when turning on the burner switch: * Check the fuel level in the tank. * Clean the fuel filter. For issues like a blocked or burnt-out fuel pump, damaged thermostat, insufficient ignition spark, incorrect electrode spacing, or a burnt-out fuse, contact an authorized service center.
Why is my Lavor MISSISSIPPI R water not hot enough?
If the water from your Lavor Washer isn't hot enough: * Clean the burner nozzle filter. * Clean the fuel filter. * Descaling the boiler coil clogged with limestone may be required. For poor boiler performance, contact an authorized service center.
General
