LawnMaster NPTGSP2617A - Battery Safety; Battery Charger Safety

4
SPECIFICATIONS
Flywheel to crankshaft
Apply a thermostable screw-thread glue onto the
FUDQNVKDIWWKUHDG3UHVFUHZWKHÀDQJHKH[DJRQQXW
(M8) and then tighten.
89-133 10-15
&OXWFKWRÀ\ZKHHO
Slide the corrugated washers onto the clutch bolts
(M6X21.5). Apply a thermostable screw-thread glue
onto the bolt thread head section. Install the bolts into
the clutch and tighten the bolts securing the clutch to
À\ZKHHO
71-89 8-10
Ignition coil to cylinder
Put the 2 screws (M5X20) through the ignition coil
and two spacers respectively. Apply a thermostable
screw-thread glue into the cylinder holes and then pre-
screw the 2 screws (M5X20). Insert a feeler gauge
RILQPPEHWZHHQWKHÀ\ZKHHODQGWKH
LJQLWLRQFRLO3UHVVGRZQWKHLJQLWLRQFRLOÀXVKDJDLQVW
the feeler gauge. Tighten the screws with a torque
spanner securing the ignition coil. Remove the feeler
gauge.
27-35 3-4
0XIÀHUWRFUDQNFDVH
3XWWKHEROWV0;WKURXJKWKHPXIÀHUDVVHPEO\
Apply a thermostable screw-thread glue onto the 2
EROWVDQGVHFXUHWKHPXIÀHUWRWKHFUDQNFDVHXVLQJ
the torque wrench.
62-71 7-8
Apply a thermostable screw-thread glue onto the
head section of 1 screw (M5X10). Pass the screw
WKURXJKWKHSRVLWLRQLQJKROHRQWKHPXIÀHUDVVHPEO\
KROGHUDQGWLJKWHQWKHVFUHZVHFXULQJWKHPXIÀHUWR
crankcase.
62-71 7-8
Pawl assembly to
crankshaft
Apply a thermostable screw-thread glue onto the
crankshaft thread. Pre-screw the pawl assembly to
crankshaft, and then tighten using the torque wrench.
62-80 7-9
$LU¿OWHUEDVHWR
carburetor
Pre-screw the nuts (M5) with washers, and then
tighten using the pneumatic tool.
27-35 3-4
Fuel tank bracket to
crankcase
Apply a thermostable screw-thread glue onto the
screw (M5X10) and pass it through the hole on fuel
tank bracket. Tighten the screw securing the fuel tank
bracket to crankcase.
27-35 3-4
Fuel tank to crankcase
Apply a thermostable screw-thread glue onto the
screw (M5X12). Pass it through the fuel tank hole.
Tighten the screw securing the fuel tank to crankcase.
27-35 3-4
Cylinder pressure plate
Apply a thermostable screw-thread glue onto the
screw (M5X10). Pass the screw through the cylinder
pressure plate hole and then tighten it onto the
cylinder.
27-35 3-4
Electric starter
assembly to crankcase
Align the 2 screw holes on the electric starter
assembly with the screw holes on crankcase. Tighten
the 2 screws (M5X60) securing the electric starter
assembly to crankcase.
27-35 3-4
Rear engine cover
assembly
Tighten the 2 screws (ST3.9X30F) to secure the rear
engine cover.
12-13 1.3-1.5