44
ROUTER TABLE OPERATION
R9PLUS Joinery System User Guide
Introduction
Leigh Bits
70-8
75-8
A B*
Bit
Diameter
3/8"
2 1/4" 8º
140-8
170
170C
e10
1 3/4"
1 3/4"
172-375
1 3/4" 172-375
1 3/4"
1 3/4"
1 3/4"
1/4" to
1/2"
8mm
140-8
170C*
5/16"
2 3/4" 172-8– – e7
1 3/4"up to
1"
8mm
5/16"
2 3/4" – – e7 172-8
1 3/4"up to
1"
8mm,
(5/16")
180C*
1/2"
3 1/2" – – –
1 3/4"
1 3/4"
up to
1 1/4"
1/2"
7/16"
2 3/8" 8º
140-8
170
170C
e10
1 3/4"3/8" to
5/8"
8mm
Max.
Cutting
Depth
C
Shank
Diameter
D
Shank
Length
E
Overall
Length
F
Angle
Use with
Straight
Bit No.
Use with
e-Bush
Use with
Collet
Reducer
*Bits 80-8 and 160 included with the R9 Plus.
*Spiral upcut bits rout cleaner and faster,
leaving a smoother finish.
80-8*
1/2"
2 9/16" 8º
160
180
180C
172-8
172-8
172-8e10
1 3/4"1/2" to
13/16"
8mm
––
e10
–
180*
1/2" 3 1/2"1 1/4" 1/2"
166*
3/16"
– –
172-8
–
– ––
– e7–
–
e10
e10
e10
Joint
Type
Box
Box
Box
Dovetail
Dovetail
Dovetail
Dovetail
Dovetail
Dovetail
Dovetail
Dovetail
Dovetail
Box
–
e10
–
–
2 7/8"5/8" 1/4"
170*
5/16" 3"7/8" 8mm,
(5/16")
173*
3/8" 3"1/8"- 1" 3/8"
166C*
3/16" 2 1/2"5/8" 1/4"
173C*
3/8" 3"1" 3/8"
160*
––
e10
1/2"
3" –
1 3/4"up to
1 1/4"
1/2"
172-8
1/2" to 8mm collet reducer
1 1/4" long. For 8mm shank bits.
172-375
1/2" to 3/8" collet reducer
1 1/4" long. For 3/8" shank bits.
e10
C
F
A
B
D
E
C
D B
E
A
R9PLUS BIT SELECTION
This chart shows all the bits that can be used on the R9PLUS.
Includes:
70-8
3/8" dovetail bit (for through dovetails)
75-8
7/16" dovetail bit (for through dovetails)
140-8
5/16" straight bit (for half-pitch through dovetails)
e7
e-Bush (for 70-8, 75-8 for half-pitch through dovetails)
166
3/16" spiral upcut bit (for box joints)
173
3/8" spiral upcut bit (for box joints)
This kit offers great savings
over individual prices.
See leighjigs.com
R9PLUS Bit Selection
R9PLUS Accessory Kit
To Next Page
Loading...
Need help?
General
