LENCO SCD-6800 - Setting the Clock; Listening to Radio

7
Version:1.0
DCconnection
ForDCoperation,pleaseinsert8pcssizeC(UM‐2)batterytobatterycompartmentandremovetheACplugfromACoutletthen
disconnecttheACcordfromACsocket.Sinceunitwilldrawlittlepowerconsumptionduringstandbymode,suggestuninstallthe
batteryduringstandbymode.












Settingtheclock
1. Setunitinstandbymode.
2. Pressand holdthe “Menu/Mem/clk‐adj” button(12),display willshow 24hour, press Skip down(11) or Skip up
(19)but tontoselect12or24hrsformat,thenpress“Menu/Mem/clk‐adj”button(12)toconfirm,thehourdigitwillflashon
LCD display (8) Press the Skip down(11) or Skip up(19) button to set the correct hour. Press the
“Menu/Mem/clk‐adj”button(12)tostorethehourthenminutedigitwillflash.
3. PresstheSkipdown(11)orSkipup(19)buttontosetthecorrectminutes.
4. Press“Menu/Mem/Menu/clk‐
adj”button(12)tostorethecorrecthour.

 Thepresettimewillberesetcompletelyifdisconnecting themainpowersupply.Youarerecommendedto
switchthesystemintostandbymodeforconvenienceusage.
 The clock will synchronous to RDS/DAB clock once receive the RDS/D AB signal if clock did not setting in
advance.

Listeningtoradio
Operation
Manualtuning
1. TurnontheunitbyOn/Offbutton(17)&thenpresstheFunctionbutton(9)untilitreachthe“FM”mode.
2. PresstheSkipdown(11)orSkipup(19)buttontotuneyourdesiredstation.
3. Adjustvolumeup/downbutton(14)forthedesiredvolumelevel.

Autotuning
1. SettheunittoFMmode.
2. Presstheautoscanbutton(18)once,unitwillstarttoscanattuningupdirectuntilradiostationreceived.Presstuningdown
button(11)onceandthenpresstheautoscanbutton(18),theunitwillscantotuningdowndirection.If
theradiodata
system(RDS)broadcastingsignalreceived,theunitwillsettheactualtimeautomatically.
3. Adjustvolumeknob(14)forthedesiredvolumelevel

FMscansetting
Afterautotuningifmanyunwantedweaknessradiostationreceived,youcanselectstrongstationonlytofiltertheweakness
signal
station.
1. InFMmode,press“Menu/Mem/clk‐adj”button(12)toenterthe“Menu”,thenpressSkipdown(11)orSkipup
(19)buttontoselect“Scansetting”.
2. Press“Stop/Enter”button(10)toenterthe“Scansetting”,thenpressSkipdown(11)orSkipup(19)buttonto
select“Strong
stationonly”.Thenpress“Stop/Enter”button(10)toconfirmthesetting.
3. Performtheautotuningoperationagainasabove.

FM&FM‐stereoreception
 TheunitwilldefaulttheFMmodeatMono.Thus,ifFMstereosignalreceived,settheFMmodetoStereobypressMenu
button(12),thenpressSkipdown(11)orSkipup(19)buttontoselectAudiosetting,pressEnterbutton(10)and
pressSkipdown(11)or
Skipup(19)againtoselectFMstereo,thenpressEnterbutton(10)toconfirm.When
stereosignalsareweakandnoisy.ItispreferabletochangetheFMmodebysameprocedure.

Hintsforbestreception:‐
FM:thereceiverhasrodantenna(6)hangingattherearcabinet.Itshouldbetotallyextendedforbestreception.