Lennox Hearth Products EDVSTPM - User Manual

1
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
INSTALLATION
INSTRUCTIONS
FOR YOUR SAFETY: Do not store or use gasoline
or other flammable vapors or liquids in the vicin-
ity of this or any other appliance.
FOR YOUR SAFETY: What to do if you smell gas:
• DO NOT light any appliance.
• DO NOT touch any electrical switches.
• DO NOT use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow your gas suppliers
instructions.
• If your gas supplier cannot be reached, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
POUR VOTRE SÉCURITÉ: Ne pas entreposer ni utiliser
d'essence ni d'autre vapeurs ou liquides inflammables
dans le voisinage de cet appareil ou de tout autre
appareil.
POUR VOTRE SÉCURITÉ: Que faire si vous sentez une
odeur de gaz:
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucun interrupteur. Ne pas vous servir
des téléphones se trouvant dans le batiment où
vous vous trouvez.
• Evacuez la piéce, le bâtiment ou la zone.
• Appelez immédiatement votre fournisseur de gaz
depuis un voisin. Suivez les instructions du
fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service dos incendies.
L'installation et service doit être exécuté par un qualifié
installeur, agence de service ou le fournisseur de gaz.
DIRECT VENT MULTI-OPEN
ELITE
®
SERIES
VENTED GAS FIREPLACE HEATERS - DIRECT VENT MODELS
P/N 850,018M REV. E 08/2007
MODELS
OTL Report No. 116-F-04-5
sledoMtlovilliMsledoMcinortcelE
MNTSVDEMNRCVDEENTSVDEENRCVDE
MPTSVDEMPRCVDEENFPVDEENLCVDE
MNFPVDEMNLCVDE
MPFPVDEMPLCVDE
A French manual is available upon request. Order Form Number
850,018CF.
Ce manuel d’installation est disponible en francais, simplement
en faire la demande. Numéro de la pièce 850,018CF.
WARNING: IF THE INFORMATION IN THIS MANUAL
IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLO-
SION MAY RESULT CAUSING PROPERTY DAM-
AGE, PERSONAL INJURY OR LOSS OF LIFE.
AVERTISSEMENT: ASSUREZ-VOUS DE BIEN SUIVRE
LES INSTRUCTIONS DONNÉ DANS CETTE NOTICE POUR
RÉDUIRE AU MINIMUM LE RISQUE D'INCENDIE OU
POUR ÉVITER TOUT DOMMAGE MATÉRIEL, TOUTE
BLESSURE OU LA MORT.
This appliance may be installed in an aftermarket perma-
nently located, manufactured home (USA only) or mobile
home, where not prohibited by local codes. This appliance
is only for use with the type of gas indicated on the rating
plate. This appliance is not convertible for use with other
gases, unless a certified kit is used.
In the Commonwealth of Massachusetts:
• Installation must be performed by a licensed plumber or
gas fitter.
See Table of Contents for location of additional
Commonwealth of Massachusetts requirements.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Summary

PACKAGING

INTRODUCTION

GENERAL INFORMATION

TYPICAL INSTALLATION

LOCATION

APPLIANCE AND VENT CLEARANCES

TYPICAL LOCATIONS

Describes common placement scenarios for the fireplace and required shelf heights.

VENT TERMINATION CLEARANCES

Vertical Vent Termination Clearances

Specifies clearances for terminating vertical vent caps relative to building components.

TYPICAL INSTALLATION SEQUENCE

Step 1. Framing

Details on constructing the appliance framing and securing it.

Step 2. Routing Gas Line

Instructions for routing the gas supply line to the appliance location.

Step 3. Install the Vent System

Guidance on installing the direct vent system components and termination.

Step 4. Field Wiring

Procedures for connecting electrical wiring for millivolt and electronic appliances.

Step 5. Optional Blower Kit Wiring

Instructions for installing and wiring an optional blower kit.

Step 6. Connecting Gas Line

Steps for making the gas line connections to the appliance.

Step 7. Installing Logs

Procedures for placing the ceramic ember panel and logs correctly.

Step 8. Checking Unit Operation

Steps to perform an initial checkout of the appliance's operation.

Step 9. Installing Glass Enclosure Panels

Instructions on how to install the glass enclosure panels securely.

Step 10. Burner Adjustments

Guidance on adjusting the air shutter for proper flame appearance.

Step 11. Hood Installation

Instructions for installing the necessary hoods on the appliance.

EXTERIOR HORIZONTAL VENT TERMINATION CLEARANCE REQUIREMENTS

FIREPLACE FRAMING SPECIFICATIONS

EDVST (See-Through)

Framing specifications for the EDVST see-through fireplace model.

EDVPF (Peninsula)

Framing specifications for the EDVPF peninsula fireplace model.

EDVCL (Corner-Left)

Framing specifications for the EDVCL corner-left fireplace model.

EDVCR (Corner-Right)

Framing specifications for the EDVCR corner-right fireplace model.

FIREPLACE SPECIFICATIONS

EDVST (See-Through)

Detailed dimensions and clearances for the EDVST fireplace model.

EDVPF (Peninsula)

Detailed dimensions and clearances for the EDVPF fireplace model.

FIREPLACE SPECIFICATIONS CONTINUED

EDVCL (Corner-Left)

Detailed dimensions and clearances for the EDVCL fireplace model.

EDVCR (Corner-Right)

Detailed dimensions and clearances for the EDVCR fireplace model.

VERTICAL OR HORIZONTAL VENTING USING SECURE FLEX KITS AND COMPONENTS

A. Install the Inner Flex Pipe

Steps for installing the inner flexible vent pipe with adapter and clamp.

B. Install the Outer Flex Pipe

Procedures for installing the outer flexible vent pipe with adapter and clamp.

C. Route Flex Vent

Guidelines for routing flexible vent pipe, maintaining clearances and avoiding kinks.

D. Install Firestop;Spacers at ceilings and walls

Instructions for installing firestop/spacers when Secure Flex penetrates walls or ceilings.

E. Attach Flex Vent to Termination

How to attach flexible vent components to Secure Flex terminations.

GAS CONVERSION KITS

Lennox Hearth Products EDVSTPM Specifications