Table of keywords
abc
15−6
L
EDB82MV752 EN 5.2
digital, 7−73
Overspeed, 2−5
P
Parameter
change/save with LECOM−A (RS232), 6−12
Non−volatile saving, 7−92 , 14−12
Using the keypad, 7−91 , 7−92 , 14−11
Parameter set, change using keypad, 6−5
Parameter set changeover
AC motor braking, 7−31
Controlled deceleration after mains failure, 7−19
Parameter set management, 7−91 , 14−11
Own settings, 7−92 , 14−12
Parameter set transfer, 7−91 , 7−92 , 14−11
Parameter sets
changeover, 7−94
Management, 7−91
Parameter setting, 6−1
basics, 6−1
code, 6−1
using the LECOM A (RS232) communication module, 6−9
via keypad, 6−2
via keypad or PC, 6−1
with bus system, 6−1
Parameters, changing/saving using the keypad, 6−5
Password
delete, 6−8
enter, 6−7
Password protection, 6−7 , 14−18
activation, 6−7
calling a protected function, 6−7
permanent deactivation, 6−8
PID controller, 7−50
Actual value selection, 7−54
Setpoint precontrol, 7−53
Setpoint selection, 7−53
PM synchronous motors, 1−2
Power control, 13−15
Power−on time, 7−89 , 14−25
Pressure control, protection against dry running, 13−1
Process controller, 7−50
"Debouncing" of digital output signal PCTRL1−LIM, 14−27
"Debouncing" of digital output signal PCTRL1−SET=ACT , 14−27
Activation of inverse control, 14−28
Actual root function value, 14−28
Control characteristics, 7−50
Delay PCTRL1−LIM=HIGH, 14−27
Delay PCTRL1−SET=ACT, 14−27
Difference threshold PCTRL1−SET=ACT, 14−27
Hide time, 14−27
hiding/unhiding, 14−28
Max. limit output, 14−27
Min. limit output, 14−27
Offset inverse characteristic, 14−27
Output inversion, 14−28
Unhide time, 14−27
Process controller setpoint
Acceleration time, 14−27
Deceleration time, 14−27
Process data output words, Free configuration, 7−79
Process variable, Calibration of application I/O, 7−88 ,
14−49
Protection against dry running, 13−1
Protection of persons, 2−5 , 4−3
with earth−leakage circuit breaker, 4−5
Protective insulation of circuits, 3−2
Protective measures, 3−2
PTC motor monitoring, 7−84
public systems, EN 61000−3−2, 4−4
Q
Quick stop, 7−27
R
Rated data
brake resistors, 11−3
integrated brake transistor, 11−2
rated data 230 V, operation with rated power, 3−5 , 3−6
rated data 400/500 V
current derating, 3−8 , 3−10
operation with increased rated power, 3−9
operation with rated power, 3−7
Reaction times of digital inputs, 7−68
Reduce response time, LECOM−B (RS485) function module,
6−14
Relay output, Configuration, 7−73
Reluctance motors, 1−2
Remote parameterisation, using keypad, 6−6
Reset, Error message, 8−7
Residual hazards, 2−5
Response in the event of communication errors, 14−21
Running optimisation, 7−13
S
S−shaped ramps, Smooth acceleration/deceleration, 7−24
Safety information, 2−1
Layout, 2−5
Other notes, 2−5
To Next Page
Loading...