Lenze E82MV222_4B - Page 268

Table of keywords
abc
15−7
L EDB82MV752 EN 5.2
Warning of damage to material, 2−5
Warning of danger to persons, 2−5
Saving parameter sets, , 7−91
Selection
Control mode, 5−4
Operating mode, 7−2
Sensor compensation
Acceleration time, 14−26
Deceleration time, 14−26
Max. activation threshold, 14−26
Min. activation threshold, 14−26
Output signal, 7−87 , 14−26
Reset, 14−26
Setpoint changeover, 7−47
Setpoint selection, 7−32 , 14−21
Bipolar, 7−36
Field, 7−34 , 14−16
Inverse, 7−37
Normalisation, 14−23
PID controller, 7−53
Selection, 14−21
unipolar, 7−36
via bus systems, 7−46
via fixed setpoint (JOG), 7−43
via motor potentiometer, 7−41
with keypad, 7−45
Setpoint selection range
Application I/O, 7−34 , 14−16
Standard I/O, 7−34 , 14−16
Setpoint source, Select, 7−32
Setpoint source selection, 7−32
Setpoint summation, 13−14
Setting range, 7−21 , 14−15
Signal flow diagram
Controller with application I/O, 14−6
Controller with standard I/O, 14−2
Motor control (MCTRL1), 14−5
Motor control (MCTRL1) with Application I/O, 14−9
Process controller and setpoint processing (PCTRL1), 14−4
Process controller and setpoint processing (PCTRL1) with
Application I/O, 14−8
Speed setpoint conditioning (NSET1), 14−3 , 14−7
Signal flow diagrams, 14−1
explanations, 14−1
Signal selection, Analog, 7−34
Jumper position, 7−34
Signal selection , digital, 7−39
Skip frequency, 7−17
Slip compensation, 7−13
Smooth acceleration/deceleration, 7−24
Software version, 7−89 , 14−18
Special motors, Operation of, 7−16
Speed control, 13−10
Speed oscillations, 7−16
Standard I/O
Setpoint selection range, 7−34 , 14−16
terminal assignment, 4−9
Start options, 7−18
Status display, 8−1
Status word, 14−24
Stopping, 7−24
Switching frequency of inverter, 7−14
noise optimised, 7−14
Switching threshold, brake chopper, 14−25
Switching window, Frequency setpoint reached, 14−26
System bus, remote parameterisation of node using keypad,
6−6
T
Table of attributes, 14−51
explanations for, 14−51
Technical data, 3−1
general data/operating conditions, 3−1
LECOM−A (RS3232) communication module, 6−9
rated data 230 V
operation with increased rated power, 3−6
operation with rated power, 3−5
rated data 400/500 V
operation with increased rated power, 3−9
operation with rated power, 3−7
Temperature ranges, 3−1 , 6−9
Terminal assignment
application I/O, 4−12
bus function modules, 4−16
standard I/O, 4−9
Terms
Controller, 1−1
Definitions, 1−1
Drive, 1−1
motec, 1−1
Thermal monitoring, motor
Sensorless, 7−82
With PTC resistor, 7−84
Threshold, Qmin, 14−15
Torque control, Sensorless with speed limitation, 7−10
Torque limitation, 13−15
Torque thresholds
Comparison value, 14−28
Delay MSET1=MACT, 14−29
Delay MSET2=MACT, 14−29
Difference threshold for MSET1=MACT, 14−29
Difference thresholds MSET2=MACT, 14−29