Appendix
5.2 Index
5−6
l
EDSVS9332P−EXT DE 2.0
Function blocks, 3−5 , 3−95
− absolute value generation (ABS), 3−95
− Addition block (ADD), 3−96
− analog input (AIN), 3−102
− Analog output (AOUT), 3−108
− Analog signal changeover switch (ASW), 3−114
− Analog−digital converter (CONVAD), 3−146
− Analog−phase converter (CONVAPH), 3−148
− AND operation (AND), 3−104
− Angle signal adaptation (PHDIV), 3−240
− Arithmetic blocks (ARIT), 3−110
− Automation interface (AIF−IN), 3−97
− Automation interface (AIF−OUT), 3−100
− Characteristic function (CURVE), 3−156
− comparator (CMP), 3−134
− Configuration code, 3−7
− Connection, 3−8
− Create connections, 3−10
− CW/CCW/QSP linking (R/L/Q), 3−245
− Dead band(DB), 3−159
− delay element (PT1−1), 3−244
− Delay elements (DIGDEL), 3−182
− Derivative−action element (DT1), 3−190
− Digital frequency output (DFOUT), 3−167
− digital frequency processing (DFSET), 3−177
− digital frequency ramp function generator (DFRFG), 3−171
− Digital inputs (DIGIN), 3−185
− Digital outputs (DIGOUT), 3−186
− Digital status signals (STAT), 3−258
− Display code, 3−7
− drive control (DCTRL)
controller inhibit (CINH), 3−162
operation inhibit (DISABLE), 3−161
quick stop (QSP), 3−161
TRIP reset, 3−162
TRIP set, 3−162
− drive control (DCTRLC), 3−160
− Edge evaluation (TRANS), 3−270
− Fixed setpoints (FIXSET), 3−202
− Flipflop (FLIP), 3−204
− Free digital outputs (FDO), 3−193
− Free piece counter (FCNT), 3−191
− Holding brake (BRK)
Applying the brake, 3−129
Setting controller inhibit, 3−130
− Holding brakes (BRK), Opening the brake, 3−129
− Holding torque (BRK), 3−127
− Input name, 3−6
− Input symbol, 3−6
− Internal motor control (MCTRL), 3−208
− Inverter (ANEG), 3−107
− Limiting element (LIM), 3−207
− Logic NOT, 3−223
− master frequency input (DFIN), 3−164
− Monitor outputs of monitoring system (MONIT), 3−218
− motor phase failure detection (MLP), 3−217
− Motor potentiometer (MPOT), 3−220
− Multi−axis synchronisation (SYNC), 3−260
− Names, 3−6
− OR operation (OR), 3−230
− Oscilloscope function (OSZ), 3−233
− Output name, 3−7
− Output symbol, 3−7
− overview, 3−14
− Parameterisation code, 3−7
− Phase conversion (CONVPHPH2), 3−155
− Phase integrator (PHINT), 3−241
− Process controller (PCTRL1), Dancer position, tension, pressure
controller, 3−237
− Ramp generator(RFG), 3−246
− Remove connections, 3−11
− Sample and hold function (S&H), 3−248
− Signal conversion (CONV), 3−144
− Signal types, 3−5
− speed setpoint conditioning (NSET), 3−225
− State bus connection, 3−259
− system bus (CAN−IN), 3−132
− system bus (CAN−OUT), 3−133
Function blocks , Freely assignable input
variables (FEVAN), 3−195
Function library, 3−1
G
Global Drive Control, configuration with, 2−3
H
Holding torque (BRK), 3−127
Homing, 3−46
Homing speed, 3−56
Homing status, 3−48
I
Internal motor control (MCTRL), 3−208
− Additional torque setpoint, 3−210
− Angle controller, Influence of angle controller, 3−214
− Current controller, 3−210
− Quick stop (QSP)
Field weakening, 3−216
Switching frequency changeover, 3−216
− Quick stop QSP, 3−215
− Speed controller, 3−212
− Speed setpoint limitation, 3−213
− Torque control, with speed limitation, 3−213
− Torque limitation, 3−211
Inverter (ANEG), 3−107
Inverting the main setpoint, 2−7
To Next Page