INSTRUCTION MANUAL
60A ESC
Leopard 60A ESC is high performance 1:10 Scale Brushless Motor Electronic Speed
Control. The speed controller is specially designed to offer high power and high
efficiency combined with low weight and compact dimensions.
INTRODUCTION
Automatic cut-off
Auto neutral setting
Auto cell system
Advanced software
Over temperature protection
Fail safe mode
Please read the following instructions to ensure, that your Leopard 60A ESC brushless
speed control always works up to your full satisfaction.
Please read and understand these instructions completely before you use this product!
SAFETY PRECAUTION
QUICK START GUIDE
The following statements need to be understood before using the Leopard 60A ESC:
The Leopard 60A ESC is intended for 1:10 scale or smaller car.
KV value <4500KV for touring car and <4000KV for buggy car.
Do not operate speed control in or around water
Do not reverse the battery wire connections! Reversing the battery polarity will
permanently damage the ESC
Disconnect battery from speed control when not in use.
Insulate exposed wire with heat shrink tubing to avoid shorts.
1.Mount the ESC and motor into the car
2.Plug in the 3 motor wires to the 3 motor wires on the ESC
3.Plug in the ESC Rx lead to CH2 on your receiver.
4.Make sure the ESC's switch is off.
5.Plug in a battery.
6.Switch on transmitter and then turn on ESC, you'll hear multiple tones and after a
few seconds you will hear another confirmation multiple tones and the ESC is ready
to go.
Input: NiMH 6 cells & LiPo 2-3 cells & LiFe 2-3 cells
Output: Max 360 Watt 54A at 25 45A at 75 , Peak 240A
Motor Support: KV<4500KV, 1:10 Scale Car
BEC: 5V, 2A
Net Weight: 72g
Dimension:48x33x29mm
SPECIFICATION
1
INSTALLATION & CONNECTION
Install the ESC according to the diagram shown below.
Switch on the transmitter. Lift the car with the 4 wheels un-touching and turn on the
ESC power. Right after turn on the power of the ESC, you will hear a multiple sound
indicating the ESC is starting work and auto-setting the throttle neutral. When succeed
in setting neutral, it will then denoted by another confirmation sound. If it is failed
setting neutral, there will be no any confirmation sound. This ESC is applicable to the
transmitter with the setting of 50% throttle 50% brake/reverse or 70%:30%.
Adjust & make sure the Throttle forward direction coincides with the ESC forward
direction. Assure the car with 4 wheels lifted un-touching. Push the throttle trigger
forwards to start motor running, pull the throttle trigger backwards & hold it. If the
system keeps braking, the throttle forward direction coincides with the ESC forward
direction. Otherwise, if the system only has a brief braking then driving reversely, the
throttle and ESC forward directions do not coincide with each other. Change the
throttle reversing switch of the transmitter, release the throttle switch, turn off & then
turn on the ESC power again. After auto set neutral & push the throttle trigger forwards
the car should also drive forward & the non-coincidence is corrected. If not, changing
any two of the motor wires will correct the non-coincidence problem.
Motor rotating direction - Slowly apply throttle to check if the motor is rotating in the
correct direction you desired.
You may need to swap the any two motor wires to get the wheels to spin in right
directions
Brushless
Motor
Brushless
Motor
Battery
Pack
Battery
Pack
Steering
Servo
Steering
servo
in CH1
Connect
to throttle
channel
Connect
controller
and motor
using supplied
connectors
Use a high quality
connector only
(not included)
On/Off
Switch
BRUSHLESS MOTOR
WIRING DIAGRAM
CH1
CH2
CH3
CH4
BATT
ESC in CH2
Receiver
2
To Next Page
Need help?
General