Leviton DECORA VPT24 User Manual

1. Setting up the Time and the Date:
a) will be flashing. Press or to select the
hour and press to confirm your choice.
b) will be flashing. Press or to select the
minutes and press to confirm your choice.
c) A or P will be flashing. Press or to select A
for AM or P for PM and press to confirm your choice.
NOTE: Daylight Savings Time shall start at 2am on the
second Sunday of March (add one hour) and end at 2am
on the first Sunday of November (subtract one hour).
d) will be flashing. Use or to choose the year
and press to confirm your choice.
e) will be flashing. Use or to choose the
month and press to confirm your choice
f) will be flashing. Use or to choose the date
and press to confirm your choice. The day of week
will automatically adjust.
2. Programming your Timer Options:
a) Setting Sunup, Sundown, desired Oset Time and
Time Zone: Sunup and Sundown are automatically
adjusted using the latitude and longitude
coordinates of your location. To obtain these
coordinates go to www.leviton.com/VPT24 and
click on Longitude/Latitude Coordinates Lookup...
Type in your home address and press enter. Your
latitude (N) and longitude (W) coordinates will be
shown on the screen. Write down only the 2 or 3
digit number. Disregard a negative symbol (–) if it
precedes the number.
Programming Guide
SET
SET
SET
SET
SET
SET
A
A
Override button
Door held open
To exit programming at any time press override button -
To program your device:
a) Perform a System Reset by gently lifting the VPT24 door
from the bottom of the push pad until an audible click is
heard. The door will stay open while you are
programming the device:
b) Press and hold followed by (Override) until
stops flashing and flashes (approximately
10 seconds). Press to confirm device Reset.
c) Product will go through a brief self test.
Pro Mode provides up to 50 ON/OFF events for any day or combination of days, M-Su, M-F, or Sa-Su at
desired fixed times or self adjusting Sunup and Sundown times. In this mode self adjusting Daylight
Savings Time and random modes are also available.
SET
SET
MENU
Do you have a California-exclusive model VPT24?
If you're unsure, press 3 times until RND displays, then press . '6 Hr' will display on California-exclusive models.
VPT24

Leviton DECORA VPT24 Specifications

General

Voltage	120VAC, 60Hz
Battery Backup	No
Style	Decora
Amperage	15A
Color	White
Material	Thermoplastic
Weight	0.3 lbs
Operating Temperature	0° to 40° C (32°F to 104°F)
Wattage	1800W
UPC	078477
Wiring	Requires Neutral Wire

Summary

Programming Your Device

Perform System Reset

Gently lift the door from the bottom until an audible click is heard.

Confirm Device Reset

Press and hold SET, then (Override) until DEL stops flashing.

Product Self-Test

The product will go through a brief self test after reset.

Setting Up Time and Date

Set Hour

Configure the hour setting for the timer.

Set Minutes

Configure the minute setting for the timer.

Set AM/PM

Select AM or PM for the current time.

Set Year

Configure the current year.

Set Month

Configure the current month.

Set Date

Configure the current date.

Programming Timer Options

Set Sunup, Sundown, Offset, and Time Zone

Configure astronomical times, offsets, and location.

Set Latitude and Longitude

Input location coordinates for automatic time adjustment.

Set Offset Time

Adjust ON/OFF times relative to Sunup/Sundown.

Select Time Zone

Choose the correct time zone based on coordinates.

Setting ON/OFF Events

Enter Programming Mode

Press MENU until PRG is in the lower left corner.

Select Event Number

Choose an existing event or move to the next for programming.

Set Event Time

Configure the ON or OFF time for the selected event.

Set Day Combination

Choose specific days or combinations for the event.

Set Event Type

Select event trigger (Sunup/Sundown) or delete.

Exit Programming

Press SET to escape programming mode.