2. Modifying a Preset
Copyright © 1990 Lexicon Inc. All rights reserved.
3 Oak Park • Bedford, MA 01730 • Tel: (781) 280-0300 • Fax: (771)280-0490
LXP-15 Quick Reference Guide
Once you've loaded a pre-
set, turn the PAGE knob to
select one of the six parame-
ter pages (Delay, Pitch/EQ,
Reverb, Level, Mod or Alg).
Each page displays a set of
parameters related to the
current setup.
Pressing the button directly
beneath a displayed parame-
ter will select it for adjust-
ment.
Turning the ADJUST knob
will display the full name of
the selected parameter and
its current value.
This value will change as you
continue to turn ADJUST .
➠
➠➠
Pressing VIEW will display
the parameters along with
their curent settings.
Note:
The screen will return to its normal 5-parameter display if
you select another parameter, or if 2 seconds pass without
further parameter adjustment. The setup name will be marked
with an asterisk (*) to indicate that the setup has been modified
since it was last stored.
Select "Scale" and use AD-
JUST to select the control
range for the Destination. As
the Source controller is
moved from min to max, posi-
tive scaling increases (nega-
tive scaliing decreases) Des-
tination values.
Turn the PAGE knob to
select one of the four "Patch"
positions. Select "Src" and
use ADJUST to select the
desired controller.
Select "Dest" and use AD-
JUST to select the parame-
ter you want to control.
Select "Thresh n" and use
ADJUST to set the Source
controller's position relative
to the initial Destination
value. (For most applica-
tions, you can simply leave
Threshold set to 0.)
➠
➠➠
3. Patching
Turn the PAGE knob to
select "Name." The current
setup name will appear in the
upper right of the display
with the first character of the
name underlined.
Turning the ADJUST knob
will cause the underlined
character to be replaced with
the first letter of the name you
want.
The ADJUST knob dials
sequentially through a list of
alphanumeric characters in
the following order: (space),
0-9, A-Z, a-z, and an assort-
ment of standard symbols.
Pressing the buttons under
"<Char" and "Char>" will step
the underline cursor to the
left and right, allowing you to
choose the characters you
want to change.
➠➠
➠
4. Naming your new setup
Turn the ADJUST knob to
select a register number be-
tween 1-128. (Make sure it's
one whose contents you
don't mind overwriting.
Press the button directly be-
neath "Reg #" on the dis-
play.
When the display shows the
register number you want,
press the button directly be-
neath "Store." The display
will indicate successful stor-
age.
Turn the PAGE knob to
select "Store."
➠
➠
➠
5. Storing a new sound
Note:
The LXP-15 will not perform a store instruction if "Memory
Protect" is enabled. This function is accessed by turning the
PAGE knob to "Sys", pressing the button directly beneath "Mem
Prot" and using the ADJUST knob to select ON or OFF.
Note:
Pressing the button directly beneath "Reg scan" on the
display allows you to scroll through the registers
without
loading
them. If you use this method of selection, press the button
directly beneath "Load" on the display to load any displayed
setup.
Turn the PAGE knob to
select "Setup."
➠
The setup is automatically
recalled.
Press the button directly be-
neath "Registr" on the dis-
play.
➠
➠
Turn the ADJUST knob to
select the register number
you want.
6. Recalling a Register
To Previous Page
Loading...
