LG 19LH20R - Page 119

01. Power (Command: k a)
To control Power On/Off of the TV.
'_'_msmsson[k][a][ ] [SetD] [ ] [Da_][Cr]
Data O0 : Power Off Data 01 : Power On
Acknowledgement [a][ ][Set [D] [ ] [OKiNG] [Data] [x]
To show Power On/Off.
TransmissiOn [k] [a][] [Set [D][ ][FF] [Cr]
Acknowledgement [a][ ][Set [D] [ ] [OKiNG] [Data] [x]
If there is the time delay between command and
ack message during power on sequence, It should
be described like "Note: In this model, TV will send
the Acknowledge after power on processing com-
pletion. There might be a time delay between com-
mand and acknowledge."
02. Aspect Ratio (Command: k c)
To adjust the screen format. (Main picture format)
You can adjust the screen format using the Aspect
Ratio in the Picture menu.
Transmission [k] [c][ ][Set [D][ ] [Da[a] [Cr]
Data 01 : 4:5 04: Zoom
02:16:9 10: Cinema Zoom1
09: Just Scan [
1F: Cinema Zoom16
Acknowledgement [c] [ ] [Set [D] [ ] [OKiNG] [Data] Ix]
Using the ROB input, you select either 16:9 or 4:3
screen aspect ratio.
Just Scan operates only in
Component/HDMl(720p/lO80VlO80p) input source.
03. Screen Mute (Command: k d)
To select screen mute on/off.
Transmission [k] [d] [ ] [Set [D] [ ] [Data] [Cr]
Data O0 : Screen mute off (Picture on)
Data 01 : Screen mute on (Picture off)
Data O0 : Video mute off
Data 10 : Video mute on
AcknowJedgement [d] [ ] [Set ID] [] [OKiNG] [Data] [x]
In case of Video mute on only, TV will display
On Screen Display(OSD). But, in case of Screen
mute on, TV will not display OSD.
04. Volume Mute (Command: k e)
To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission [k] [e][ ] [Set [D][ ][Data] [Cr]
Data O0 : Volume mute on (Volume off)
Data 01 : Volume mute off (Volume on)
Acknowledgement [e][ ][Set [D][ ] [OKiNG] [Data] [x]
0S.
Volume Control (Command: k f)
To adjust volume.
You can also adjust volume with the volume buttons
on remote control,
Transmission [k] [f] [ ][Set [D][ ][Data] [Cr]
Data Min : O0 - Max : 64
Refer to 'Real data mapping'.
Acknowledgement [f] [ ] [Set [D][ ][OKiNO] [Data] [x]
06.
Contrast (Command: k g)
To adjust screen contrast.
You can also adjust contrast in the Picture menu.
Transmission [k] [g] [ ] [Set [D] [ ] [Data] [Cr]
Data Min : O0 - Max : 64
Refer to 'Real data mapping'.
Acknowledgement [g] [ ] [Set [D] [ ] [OK] [Data] [x]
07.
Brightness (Command: k h)
To adjust screen brightness.
You can also adjust brightness in the Picture menu.
Transmission [k] [h] [ ] [Set [D] [ ] [Data] [Cr]
Data Min : O0 - Max : 64
Refer to 'Real data mapping'.
Acknowledgement [h] [ ] [Set [D] [ ] [OKiNG] [Data] [x]
08. Color (Command: k i)
To adjust the screen color.
You can also adjust color in the Picture menu.
Transmission [k] [i] [ ] [Set [D] [ ] [Data] [Cr]
Data Min : O0 - Max : 64
Refer to 'Real data mapping'.
Acknowledgement [i] [ ] [Set [D] [ ] [OKiNG] [Data] [x]
09. Tint (Command: k j)
To adjust the screen tint.
You can also adjust tint in the Picture menu.
Transmission [k] D][ ][Set [D][] [Data] [Cr]
Data Red : O0 - Green : 64
Refer to 'Real data mapping'.
Acknowledgement [j][ ][Set ID][ ][OK/NO] [Data] [x]
-D
-D
Z
X
119