25
206-4278
Installer Menu Items 073 through 122
Item Function Value Range Default Value Brief Description of Function
073 CH NOT AVBLE 0 / 1 0
If set to 1 and item 028 CH. OVERIDE is set to 0, a “CHANNEL NOT
AVAILABLE” message is displayed if user attempts to direct tune a channel that
is not included in the channel lineup.
075 REVERT CH 0 / 1 0 If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel.
078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte.
079 UPN MSB-1 0 ~ 255 0 User programmable number, most significant byte - 1.
080 UPN MSB-2 0 ~ 255 0 User programmable number, most significant byte - 2.
081 UPN LSB 0 ~ 255 0 User programmable number, least significant byte.
082 CHKSM ERROR 0 / 1 1 Enforces rigid MPI checksum.
083 HANDSHK TIME 0 ~ 5 5 Relaxes MPI timing to be compatible with PC-based Windows-controlled systems.
084 PERMANENT BLK 0 / 1 0 Removes block hours setting for Parental Control and makes block permanent.
086 V. MUTE TIME 0 ~ 50 0 Use to extend the normal video mute time during channel change.
087 REAR RGB EN.
0
,
1, 17
1
Dependent on item 093 RJP AVAILABLE setting. Set to 0 to disable RGB input.
Set to 1 to enable RGB input. Set to 17 for Auto Configure.
088 EN NOISE MUTE 0 / 1 1 (Analog channels only) If set to 1, audio is muted if no signal is present.
090 KEY LOCK 0 / 1 0 If set to 1, all display panel joystick button functions are locked. IR is still functional.
091 HDMI2 ENABLE 0 ~ 2 1
Set to 0 to disable HDMI 2. Set to 1 (DTV Mode) or 2 (PC Mode), as
applicable, to enable HDMI 2.
092 HDMI3 ENABLE 0 ~ 2 1
Set to 0 to disable HDMI 3. Set to 1 (DTV Mode) or 2 (PC Mode), as
applicable, to enable HDMI 3.
093 RJP AVAILABLE 0, 1, 2, 5, 6 0
Set to 0 to disable. Set to 1, 2, 5, or 6 for HDMI or DVI Mode. (See
detailed descriptions.)
094 SAP MENU EN 0 / 1 1 Set to 1 to enable SAP feature in Function Menu.
096 DEF. ASP. RATIO 0 ~ 4 2 Sets default aspect ratio at power up. See detailed descriptions and item 106.
097 AUDIO OUTPUT 0 ~ 9
7
Set as required in accordance with external audio equipment connected to the
TV. See detailed descriptions.
098 PRO:CENTRIC 0 ~ 2
0
Set to 0 to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for
GEM (Java Application) Mode.
099 BACK LIGHTING 1 ~ 200, 255 255 Sets the level of the TV picture back lighting. (See detailed descriptions.)
102 ATSC BAND 0 ~ 4 4 Selects ATSC band.
103 ATSC TUNE MODE 0 / 1 1 Set to 1 (default) for Physical Channel scan. Set to 0 for Virtual Channel scan.
104 START MINOR CH 0 ~ 255 0 Selects Minor Start Channel. Set to 0 for NTSC.
106 ASP RATIO LOCK 0 / 1 0
To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on
power cycle.
116 VIDEO MUTE EN 0 / 1 0
(Analog channels only) If set to 1, video mutes (blank screen) when no
signal is present.
117 FACT DEFAULT 0 / 1 0 Set to 1 to restore the factory default settings of all Installer Menu items.
118 POWER SAVINGS 1, 3, 7 3
Determines the powered status of the embedded b-LAN module and the GAME
CONTROL/MPI port. (See detailed descriptions.)
119 DATA CHANNEL
0 ~ 135, 253,
255
255
Set to 0 to disable. Set from 1 to 135 to match the RF channel number used by
the Pro:Centric server as its data channel. Set to 255 to use Auto Search to find
the Pro:Centric RF channel. (See detailed descriptions.)
121 UPDATE TIME HR 0 ~ 23, 128 128
Sets the Wake For Update hour. The value “128” is displayed as “OFF.” Directly
entering 128 turns the Wake For Update feature OFF.
122 UPDATE TIME MN 0 ~ 59 0 Sets the minute for Wake For Update.
Installer Menu (Cont.)
To Next Page
Loading...
