How often should I change screen on LG 43TNF5J-B Digital Signage?
It is recommended that you change the screen at least once every 12 hours at the very minimum; if done more frequently, the prevention of image sticking is more effective.
Why does voltage difference cause image sticking on LG Digital Signage?
When the LCD panel displays a static image for an extended period of time, it can cause a voltage difference between the electrodes that operate the liquid crystals. When the voltage difference between the electrodes builds up over time, liquid crystals have a tendency to remain aligned in one direction. During this process, a previously displayed image remains visible. This phenomenon is referred to as image sticking.
How to prevent after-image on LG 43TNF5J-B Digital Signage?
To prevent after-images on your LG Digital Signage: * If you use a fixed image for a long time, the pixels may be damaged. Use the screen-saver function. * When a dark image is displayed on the screen after an image with high contrast (black and white or gray), this may cause image sticking. This is normal for display products.
How to fix multi-touch not responding on LG Digital Signage?
If multi-touch is not responding on your LG Digital Signage: * Make sure that you use a content that supports Multi-touch point. The content played (e.g. Flash Player, Paint, etc.) may not support Multi-touch points. * Remove the USB cable and connect it again in 10 seconds. * Run the content (e.g. Flash Player, Paint, etc.) again. * Restart your PC. * On the edge of the touch screen, multi-touch may work unstably. * If the interval between two touches is too short, a touch error may occur.
How to correct touch location on LG 43TNF5J-B Digital Signage?
If the location of a touch does not correspond to the touch coordinates on your LG Digital Signage, this may occur when the touch screen is not calibrated properly. Change your tablet PC settings.
How to fix PC BIOS configuration screen not displayed correctly on LG 43TNF5J-B?
On some PCs, the BIOS configuration screen may not display correctly because the atypical aspect ratio is not supported before the graphics card driver is configured. To access the PC BIOS configuration screen, please connect a standard aspect ratio (4:3 or 16:9) monitor, then perform the BIOS configuration.
Why won't my LG 43TNF5J-B Digital Signage turn on?
If your LG Digital Signage isn't powering on, here are a few things to check: * Ensure the power cord is securely plugged into the power outlet. * If operating in below-zero temperatures, allow up to one hour for the enclosure to warm up internally. * For models with a circuit breaker, verify it's properly connected and the switch is set to the 'on' position (red). * Try disconnecting and reconnecting the AC adapter, after cleaning the contacting port. * When using POE, make sure that the LAN cable is not damaged. * Do not connect the AC adapter when using POE power.
How to fix dull sound on LG Digital Signage?
To fix dull sound on your LG Digital Signage, select the appropriate equalizer sound.
What to do if the image is not displayed on LG 43TNF5J-B Digital Signage?
If the image is not displayed on your LG Digital Signage, check that the cable is properly connected between the panel and the Signage box.
How to fix horizontal noise or blurred characters on LG 43TNF5J-B?
To correct horizontal noise or blurred characters on your LG Digital Signage, if using a D-Sub analog signal, press the button on the remote control to automatically select the optimal screen status that fits into the current mode. If the adjustment is not satisfactory, adjust the display settings manually in the OSD menu.
General| Panel Technology | IPS |
|---|---|
| Contrast Ratio | 1200:1 |
| Dynamic Contrast Ratio | 500, 000:1 |
| Viewing Angle (H x V) | 178° x 178° |
| Life Time | 50, 000 Hours |
| Operation Hours | 24/7 |
| Orientation | Landscape & Portrait |
| VESA Mount Standard | 200 x 200 mm |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -20°C to 60°C |
| Standby Power Consumption | 0.5W |
| Input Voltage | 100-240V~, 50/60Hz |
| Frequency | 50/60Hz |
| Screen Size | 43 inch |
| Native Resolution | 1920 x 1080 (FHD) |
| Surface Treatment | 3H |
| Input | HDMI, DVI-D, USB |
| Output | Audio |
| External Control | RS232C, RJ45 |
| Ports | HDMI, USB, RS-232C, RJ45 |
| Response Time | 12 ms (G to G) |
To Next Page
