01. Power (Command: k a)
To control Power On/Off of the TV.
Transmission[k][a][] [Set!D][ ][Data][Cr]
Data 00: Power Off Data 01 :Power On
Acknowledgement [a][ ] [Set ID] [ ] [OK/NG] [Data] [x]
In a like manner, if other functions transmit 'FF' data
based on this format, Acknowledgement data feedback
presents status about each function.
Note: In this model, TV will send the Acknowledge
after power on processing completion.
There might be a time delay between command and
acknowledge.
02. Input Select (Command: x b)
To select input source for TV.
Transmission[x][b][][SetlD][ ] [Data] [Cr]
Data 00: DTV (Antenna) Data 01 : DTV (Cable)
Data 10: Analog (Antenna) Data 11: Analog (Cable)
Data 20:AV1 Data 21 : AV2
Data 40:Component1 Data 41 : Component 2
Data 60: RGB-PC Data 90:HDMI1
Data 91:HDMI2 Data 92:HDMI3
Data 93:HDMI4
Acknowledgement [b][ ][Set ID][ ][OK/NG] [Data] [x]
03. Aspect Ratio (Command: k c)
To adjust the screen format.
Transmission [k] [c] [] [set ID] [] [Data] [Cr]
Data 01 : 4:3 09: Just scan
02:16:9 10: Cinema Zoom1
04: Zoom
06: Set by program 1 F: Cinema Zoom16
Acknowledgement[c][ ][Set ID][ ][OK/NG] [Data] [x]
04. Screen Mute (Command: k d)
To select screen mute on/off.
TransmissiOn[k] [d][] [Set ID] [] [Data] [Cr]
Data 00: Screen mute off (Picture on), Video-out Mute off
Data 01 : Screen mute on (Picture off)
Data 10: Video-out Mute on
Acknowledgement[d][] [set ID] [ ] [OK/NG] [Data] [x]
In case of Video-out Mute on only, TV will display On
Screen Display (OSD). But, in case of screen mute on,
TV will not display On Screen Display (OSD).
05. Volume Mute (Command: k e)
To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
TransmiSsiOn[k] [e][ ][Set ID][ ][Data] [Cr]
Data 00: Volume mute on (Volume off)
Data 01: Volume mute off (Volume on)
AcknowledgemenL [e][ ][set ID][ ][OK?NG] [Data] [x]
06.
Volume Control (Command: k f)
To adjust volume.
You can also adjust volume with the volume buttons on
remote control.
Transmission[k] [f] [] [Set ID][] [Data] [Cr]
Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
*Refer to 'Real data mapping'.
Acknowledgement[f] [] [Set ID][] [OKiNG] [Data] [x]
07.
Contrast (Command: k g)
To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission[k] [g][] [Set ID] [] [Data] [Cr]
Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
_Refer to 'Real data mapping'.
Acknowledgemen_ [g][ ][Set ID][ ] [OKiNG] [Data] [x]
08.
Brightness (Command: k h)
To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission[k] [h][] [Set ID] [ ] [Data] [Cr]
Data Min: 00 _ Max: 64 (*transmit by Hexadecimal code)
_Refer to 'Real data mapping'.
Acknowledgemen_ [h][ ][Set ID][ ] [OKiNC] [Data] [x]
09.
Color (Command: k i)
To adjust screen color.
You can also adjust color in the PICTURE menu.
Transmission[k] [i] [ ] [set ID][] [Data] [Cr]
Data Min: 00 _ Max: 64 (*transmit by Hexadecimal code)
_Refer to 'Real data mapping'.
Acknowledgement[i] [] [Set ID] [] [OK/NG] [Data] [x]
10.
Tint (Command: k j)
To adjust screen tint.
You can also adjust tint in the PICTURE menu.
Transmission [k] [j][] [Set ID][ ] [Data] [Cr]
Data Red: 00 _ Green: 64 (*transmit by Hexadecimal code)
*Refer to 'Real data mapping'.
ACknowledgemen_[j ][] [Set ID] [ ] [OK/NG] [Data] [x]
-O
-O
m
Z
E3
X
123
To Next Page
Loading...
