LG DLEX0001TM - User Manual

Other manuals for LG DLEX0001TM

Service Manual54 pages

Specifications2 pages

Questions and Answers

D
david60Sep 23, 2025
What does 'END OF CYCLE' with 2 bars on my LG Dryer LCD mean?
- C
  Carrie WongSep 23, 2025
  If 2 bars are displayed on the LCD screen of your LG Dryer with the message "END OF CYCLE", it suggests that the ductwork is slightly too long or has too many turns/restrictions, or there's a partial blockage due to lint buildup. Install a shorter or straighter duct run. The ductwork should be checked/cleaned soon. The dryer can be used in this condition, but drying times may be longer. If the message is displayed after the end of the cycle, it will turn off in 4 minutes, or immediately if the POWER button is pressed or the door is opened.
M
melinda57Aug 23, 2025
Why is my LG DLEX0001TM Dryer not heating up?
- M
  mvegaAug 23, 2025
  If your LG Dryer isn't heating, check the house fuse or circuit breaker and reset it or replace the fuse if necessary, without increasing its capacity. If it's a gas model, ensure both the house gas shutoff and the dryer gas shutoff are fully open. If a circuit overload is the issue, consult a qualified electrician.
N
natalie49Aug 25, 2025
What to do if my LG DLEX0001TM Dryer says 'Add Water'?
- A
  Andrew MartinAug 25, 2025
  If the LG Dryer displays 'Add Water', it means the sensors haven't detected that the steam generator is full within 60 seconds. To resolve this, fill the feeder and restart the cycle.
M
Michele MurphyAug 27, 2025
What does tE4 mean on my LG Dryer?
- B
  Brittany JonesAug 27, 2025
  If your LG Dryer displays the error code tE4, it indicates that the steam generator thermistor is either open or shorted. The suggested solution is to replace the steam generator.
R
Richard MoranAug 27, 2025
Why does my LG DLEX0001TM Dryer display or BULKY LOAD?
- T
  Tammy VasquezAug 28, 2025
  If the display shows or BULKY LOAD on your LG Dryer, pressing the MORE TIME button several times will set the cycle for a big load such as a comforter.
M
Michael TuckerSep 18, 2025
What does 'NEED FLOW CHECK' with 4 bars on my LG Dryer LCD mean?
- T
  Thomas ReevesSep 18, 2025
  If 4 bars are displayed on the LCD screen of your LG Dryer with the message "NEED FLOW CHECK," it indicates a significant blockage in the ductwork due to lint buildup or debris. Install a shorter or straighter duct run. The ductwork should be checked and cleaned soon. The dryer can be used in this condition, but drying times may be longer. If the message is displayed after the end of the cycle, the dryer will turn off in 2 hours, or immediately if the POWER button is pressed or the door is opened.
K
Kathleen GarciaSep 15, 2025
What does WATER SUPPLY ERROR mean on my LG DLEX0001TM display?
- D
  daleandersonSep 15, 2025
  If your LG Dryer displays a WATER SUPPLY ERROR, check the steam feeder drawer. Ensure it's filled with water to the MAX line, properly seated, and fully closed. Then, turn the dryer off and restart the Steam cycle.
E
Erin DavisSep 16, 2025
Why do odors remain after using STEAM FRESH™ on my LG Dryer?
- J
  Jeremy FergusonSep 17, 2025
  If odors remain in clothing after using the STEAM FRESH™ cycle on your LG Dryer, it means the cycle did not completely remove the odor. Fabrics with strong odors should be washed in a normal cycle.
M
Miguel CarlsonSep 6, 2025
Why is there lint on clothes after using my LG DLEX0001TM?
- S
  Sherry DukeSep 6, 2025
  To prevent lint on clothes when using your LG Dryer: * Clean the lint filter before every load, and possibly during cycles with high lint production. * Sort laundry properly, separating lint producers from lint trappers. * Avoid overloading the dryer. * Check pockets for tissues or paper before washing and drying.
J
Jeffrey MoodySep 3, 2025
Why does water drip from the nozzle when the Steam Cycle starts on my LG DLEX0001TM Dryer?
- K
  Kara BartonSep 4, 2025
  This is steam condensation. The dripping water will stop after a short time.