What does an over current error mean on my LG Washing machine?
If your LG Washing machine shows an over current error, it means that either the MAIN PWB ASSEMBLY is out of order or the winding in the STATOR ASSEMBLY is short-circuited. Check both the MAIN PWB ASSEMBLY and STATOR ASSEMBLY.
What does it mean if my LG Washer shows a LOCKED MOTOR ERROR?
A LOCKED MOTOR ERROR in your LG Washer can be caused by several issues: 1. The MOTOR HARNESS connector is not connected to the STATOR ASSEMBLY connector. 2. Bad or unstable electrical contact between connectors in the MOTOR HARNESS and the MAIN PWB ASSEMBLY. 3. The MOTOR HARNESS between the STATOR ASSEMBLY and MAIN PWB ASSEMBLY is cut. 4. The hall sensor is defective.
Why won't my LG WD-11270BD start?
The LG washer might not start due to several reasons: * The power cord may not be properly plugged in. Ensure the plug fits tightly into the wall outlet. * A blown fuse or tripped circuit breaker could be the issue. Reset the circuit breaker or replace the fuse. Do not increase fuse capacity. If it's a circuit overload, consult a qualified electrician. * The water supply tap might not be turned on. Make sure to turn it on. * The door might not be firmly shut. Close the door properly and press the Start/Pause button. Note that it may take a few moments for the washer to begin spinning after pressing the button, as the door must lock first.
What to do if my LG WD-11270BD is leaking water?
If you notice water leaks from your LG washer, here are some potential causes and solutions: * Check if the fill hose connection is loose at the tap or washer and tighten it. * Ensure that house drain pipes are not clogged. Unclog the drain pipe or contact a plumber if necessary. * Too much or unsuitable detergent can cause leaks. Reduce the amount of detergent or switch to a low-sudsing detergent. * Verify that the water supply is adequate in your area by checking another tap in the house. * Make sure the water supply tap is fully open. * Inspect the water inlet hose for any bends and straighten it. * Check the filter of the inlet hose for clogs. * Examine the drain hose for bends or clogs and clean and straighten it. * Clean the drain filter if it is clogged.
Why my LG Washer does not start?
If your LG Washer doesn't start or won't spin, ensure the power cord is securely plugged into the wall outlet. Check your house fuse or circuit breaker, and reset it if necessary. Make sure the water supply tap is turned on. Also, verify that the door is firmly shut; press the Start/Pause button, keeping in mind that it may take a few moments for the washer to begin spinning after the door locks.
What does it mean if my LG WD-11270BD displays an OVER CURRENT ERROR?
An OVER CURRENT ERROR in your LG Washer indicates that the MAIN PWB ASSEMBLY is out of order or the winding in the STATOR ASSEMBLY is short-circuited.
Why does my LG WD-11270BD Washer have a DOOR OPEN ERROR?
A DOOR OPEN ERROR can occur in your LG Washer if the door is not completely closed, there are loose electrical connections at the door switch and PWB assembly, or the DOOR SWITCH ASSEMBLY is out of order.
What causes a HEATING ERROR in my LG WD-11270BD?
A HEATING ERROR in your LG Washer is caused by the THERMISTOR being out of order.
What does WATER INLET ERROR mean on my LG Washer?
A WATER INLET ERROR on your LG washer means that the correct water level isn't reached within 8 minutes after water is supplied, or it doesn't reach the preset water level within 25 minutes.
What causes a DOOR OPEN ERROR on an LG WD-11270BD Washer?
A DOOR OPEN ERROR on your LG washer indicates that the door isn't completely closed, there are loose electrical connections at the door switch and PWB assembly, or the DOOR SWITCH ASSEMBLY is faulty.
To Next Page
General
