Lincoln 877 - User Manual

To Next Page

Page

Section

- F22

- 6C

Form 404130

JULY 2010

MODEL 877

METERING CONTROL VALVE

Series “A”

SPECIFICATIONS:

Dial Capacity 32 Ounces - 16 Quarts

Totalizer Quarts

Flow Max. 4 Gallons per min. (15 liters per min.)

Flow Min. 0.4 Gallons per min. (1.5 Liters per min.)

Operating Pressure Max. 1000 PSI (70 Bar)

Operating Temp. Max. 110° F (45° C)

Accuracy +/- 0.65%

Weight 3.3 Lbs. (1.5 Kg.)

Meter Inlet Threads 1/2 NPT

(IOM-094-02 P/N 53400-094

Rev. 2)

New metering systems must be purged prior to installation

of metering control calce to free system of contaminates.

The automatic nozzle requires 60 PSI to open and function

properly. A pump exceeding 60 PSI is required for adequate

ﬂ ow and proper operation. A pump ratio of at least 3:1 os

recommended.

OPERATION

The meter can handle petroleum products such as automatic

transmission ﬂ uid, S.A.E. 5 to 50 weight motor oil, S.A.E. 80 to

240 weight gear oil and antifreeze ﬂ uid (ethylene glycol).

The meter can be locked in the on position by engaging the trig-

ger lock, to release the lock the trigger must be depressed thus

releasing the lock. Before each use reset the meter by rotating

the indicator knob counterclockwise to zero.

HOSE

91241

84799 NOZZLE

(NON-DRIP)

90464

SWIVEL

68410

BASIC METER

TURN TO OPEN

NOZZLE

Systems which will be dispensing ﬂ uids under pressure

may need to be protected by using a thermal relief kit which

will safely limit the pressures caused by thermal expan-

sion. Please contact your local Lincoln distributor and refer

to Section K5, Page 31 for more details. Failure to include

thermal relief protection may cause damage not covered

under Lincoln’s warranty policy.

WARNING

IMPORTANT NOTE:

Indicates change

Americas:

One Lincoln Way

St. Louis, MO 63120-1578

USA

Phone +1.314.679.4200

Fax +1.800.424.5359

Europe/Africa:

Heinrich-Hertz Str 2-B

D-69183 Waldorf

Germany

Phone +49.6227.33.0

Fax +49.6227.33.259

Asia/Paciﬁ c:

25 Int’l Business Park

#01-65 German Centre

Singapore 609916

Phone +65.562.7980

Fax +65.562.9967

www.lincolnindustrial.com

Need help?

Do you have a question about the Lincoln 877 and is the answer not in the manual?

Summary

Troubleshooting Meter Control Valve Issues

No Material Flow Troubleshooting

Diagnoses causes for complete lack of fluid dispensing from the meter.

Partial Material Flow Diagnosis

Addresses issues leading to reduced or insufficient fluid output.

Metering Indicator Discrepancies

Covers scenarios where the odometer or indicator fails to register or turn.

Leaks and Faulty Nozzle Issues

Details causes for leaks after shut-off, oil leaks, and faulty nozzles.

Pre-Set Operation Mode

Explains the condition of 'Pre-Set Only' without auto shut-off.

Safety and Operational Guidelines

Thermal Relief Protection

Importance of thermal relief kits for dispensing fluids under pressure.

System Purging Procedure

Requirement to purge new metering systems before installation.

Automatic Nozzle Pressure Requirements

Specifies the minimum pressure needed for proper nozzle operation.

Meter Operation and Specifications

Fluid Compatibility and Operation

Lists compatible petroleum products and basic operational steps.

Performance and Physical Specifications

Details dial capacity, flow rates, pressure, temperature, accuracy, and weight.

Service Parts and Component Identification

Meter Component Breakdown

Identifies and lists part numbers for meter components.

Pointer Operation Caution

Warns against turning the pointer clockwise to prevent damage.