Linear 2GIG-TS1 - User Manual

INSTALL INSTRUCTIONS
Thisdocumentdescribesthebasicinstallationinformationforthe2GIG‐
2GIG‐TS1andthestepsnecessaryto“pair”(orlearnin)theTouchscreen
WirelessKeypadtotheControlPanel.
Box Contents
•2GIG‐TS1
•ACPowerSupply
•ACPowerSupplyBracket
•Screwsandanchors
TIP: Theboxcontentswillvarydependingonwhetherthe2GIG‐TS1
waspurchasedaspartofakitornot.
BEFORE YOU BEGIN
Is the 900 MHz Transceiver installed in the Panel?
Forthe2GIG‐TS1tocommunicatewiththeControlPanel,the900MHz
Transceiver(2GIG‐XCVR2)mustbealreadybeinstalledintheControl
Panel.
Is the 2GIG-TS1 paired with the Control Panel?
The2GIG‐TS1andtheControlPanelhavetobepairedtocommunicate
witheachother.
To check for to see if the 2GIG-TS1 is paired with the
Control Panel
Uponpowerup,the2GIG‐TS1displaysthefollowingscreen:
2GIG-TS1 PRODUCT OVERVIEW
TheModel2GIG‐2GIG‐TS1TouchScreenWirelessKeypadisaremote
controldevicethatoffersthefunctionalityofasystemkeypadbutalso
extendsallusercontrolofthe2GIGControlpaneltootherlocationsina
user ’shome.Usingthe 2GIG‐TS1,userscancontrollights,thermostat
anddoorlo
cksandseethestatusofeveryzoneintheirhomeusingthe
exactsameandfamiliarinterfacefoundontheControlPanel.Thekeypad
isdesignedforindooruseonly.
IMPORTANT: NotforUL985installations.
Thepanelandbuttonsserveascontrolsaswellasindicators.
Pressingthe(Emergency)buttondisplaysemergencyiconsonthe
displayforPanic,Fire,andEmergencyalarmactivation(eachhas
programmableoptionsandcanbeenabledordisabled).Pressingthe
(Home)buttonchangesthesystemdisplaytotheHomeScr
een.The
keypadispoweredfromaplug‐inpowersupply.The2GIG‐TS1ex changes
informationthroughasecure2‐wa ywirelessconnectionwiththeControl
Panel.
NOTE: Beforeusingthe2GIG‐TS1itmustbe“learned”intothe
ControlPanel.
Mounting Tools
Somespecialtoolsmayberequiredtomountthe2GIG‐TS1ontothe
wall:
•Screwdriver
•Pencil
•Wirestripper
•Staplegun
•Drywallsaw(orequivalent)
• Ladder
PREPARING THE KEYPAD
NOTE: Checkthatthe2GIG‐TS1Keypadisfunctioningbefore
selectingalocationfortheKeypad.
1 Remove the screw.
2 Flip open the back cover of the 2GIG-TS1.
3 Disconnect the hanging strap.
4 Use the back cover as the mounting plate.
2GI
Touch Screen Wireless Keypad
ForRemoteControlofthe2GIG SecuritySystem

Summary

Install Instructions

Box Contents

Lists items included in the 2GIG-TS1 package, which may vary.

Before You Begin

Checks prerequisites like transceiver installation and prior panel pairing.

2 GIG-TS1 Product Overview

Mounting Tools

Lists special tools required for mounting the 2GIG-TS1 keypad to a wall.

Preparing the Keypad

Selecting a Location for the Keypad

Mounting the Keypad

Attaches the mounting plate to the wall using screws and routes wiring.

Wire Size and Length

Details recommended wire gauge and maximum lengths for proper power connection.

Connect the Power Wires to the Keypad

Learning;Pairing the Keypad with the Control Panel

Resetting a 2 GIG-TS1 to Factory Defaults

Secret Duress Button

Firmware Version Check

Removing a 2 GIG-TS1 from a Control Panel

Regulatory Information

Wireless Product Notice

General information on wireless communication limitations and FCC rules.

FCC Notice

Details FCC compliance, interference, and user actions for radio frequency energy.

Industry Canada Notices

Outlines Industry Canada compliance and user responsibilities for radio devices.

Operating and Storage Temperature

Specifies recommended temperature ranges for Touch Screen use and storage.

Limited Warranty

Outlines the warranty terms and conditions for the 2GIG Technologies product.

Linear 2GIG-TS1 Specifications

General

Wireless Frequency	900 MHz
Battery Backup	Yes
Operating Temperature	32°F to 120°F (0°C to 49°C)
Backlight	Yes
Keypad Type	Touchscreen
Compatibility	2GIG GC2, 2GIG GC3