Linear WT00Z-1 - User Manual

1
NOTE: This module must be “included in the Network” only where it will be permanently installed. The proper operation of this node in the
mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” confi gure this module.
WTOOZ-1 WALL MOUNTED TRANSMITTER
Linear’s family of Z-Wave certifi ed wireless lighting controls (switches,
dimmers, outlets and plug-in modules) brings a new level of intelligent
wireless capability to commercial and residential environments.
The Z-Wave wireless protocol is an international wireless standard
for remote home automation, security and other applications.
Embedded in each device, the Z-Wave smart chip enables two-way RF
communication among hundreds of Z-Wave enabled devices, allowing
products and services from multiple manufacturers to work seamlessly.
Linear Z-Wave products are easy to install, and allow dealers to create
an integrated wireless network with nearly limitless expansion and
interoperability with security and health monitoring systems, energy
management, home entertainment, appliances, and more.
INSTALLATION
DANGER! SHOCK HAZARD. Read and understand these
instructions before installing. This device is intended for installation in
accordance with the National Electric code and local regulations in the
United States, or the Canadian Electrical Code and local regulations
in Canada. It is recommended that a qualifi ed electrician perform this
installation. Retain instructions for future use. With power off, wire this
WT00Z-1 according to the diagram shown above. If more than one
WT00Z-1 is to be installed in a wall box, scored tabs on the side can
be broken off by bending back and forth with pliers, to accommodate
proper fi t. Apply power when completed. Refer to your Controller
operating instructions on how to include this module in the RF network
INCLUDING WT00Z-1 TO THE NETWORK
STEP 1. Prepare the Controller to include a unit to the network by
adding it to a group (method of adding a node to the network). Refer
to controller instructions.
STEP 2. The WT00Z-1 must be in its permanently installed
location. Tap either the top or bottom of the WT00Z-1 once.
STEP 3. You should see an indication on your Controller that the
“device was included” in the network.
NOTE: If you have trouble adding the WT00Z-1 to a group it may be
that the Home ID and Node ID were not cleared from it after testing.
You must fi rst “RESET UNIT” with your controller to remove it from
the network. Although adding it to a group includes it in the network,
removing it from a group does not remove it from the network. If
removed from a group, it functions as a repeater (only). “RESET UNIT”
removes it completely from the network.
WT00Z-1
Radio Frequency (RF) Controlled, 120 VAC, Wall Mounted
Transmitter, Series 300
SUPPLIED WITH DECORATIVE SWITCH PLATE
NEUTRAL
120 VAC
PUSH ON (PUSH
& HOLD TO BRIGHTEN)
WHITE
LINE
BLACK
PUSH OFF
(PUSH AND
HOLD TO DIM)
STATUS LED
GREEN
GROUND
PUSH TOP OR
BOTTOM OF PADDLE
SWITCH ONCE TO
INCLUDE IN NETWORK
TO MOUNT MORE THAN ONE
WT00Z-1IN A BOX, SCORED TAB
WILL BREAK FLUSH WITH EDGE
OF PLASTIC

Summary

Product Overview and Installation

WTOOZ-1 Wall Mounted Transmitter

Introduces the Z-Wave certified wireless lighting control transmitter and its capabilities.

Installation Instructions

Details on physical installation, wiring, safety warnings, and local codes.

Including WT00 Z-1 in the Network

Step-by-step guide for adding the device to a Z-Wave network.

Operation and Control

Basic Operation

Instructions on how to turn Z-Wave devices on/off and dim/brighten.

Associating Z-Wave Devices

Guides on linking devices to control groups for various functions and actions.

Configuration and Customization

Dimming Command Parameters

Adjusts dimming behavior, start levels, and transmission settings.

Group and LED Settings

Configures Group 4 behavior, night light function, and LED indication.

Dim Rate and Switch Inversion

Customizes dimming speed, local control rates, and paddle switch logic.

Shade Control and Polling

Enables shade control via groups and configures network polling.

Technical Specifications and Compliance

Specifications

Details power, signal frequency, and operational range of the device.

Interoperability

Explains how the WT00Z-1 integrates with other Z-Wave devices.

Regulatory Information

Provides FCC and IC compliance notices and user guidelines.

Warranty Information

Outlines the product's warranty terms and conditions.

Linear WT00Z-1 Specifications

General

Frequency	908.42 MHz
Compatibility	Z-Wave
Modulation	FSK
Output Power	1 mW
Operating Temperature	32°F to 104°F (0°C to 40°C)
Type	Transmitter