Lite Source LS-80910 - User Manual

ITEM NO.:LS-80910
VERY IMPORTANT
PLEASE READ THOROUGHLY. MAKE SURE YOU PROPERLY ALIGN POLES BEFORE YOU START TO
SCREW THEM TOGETHER. TO AVOID DAMAGING CONNECTION THREADS. NOT ADHERING TO THIS
PROCEDURE MAY VOID YOUR WARRANTY!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE. ELECTRIC SHOCK EXPOSURE TO EXCESSIVE UV
RADIATION OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS LIGHTED LAMP IS HOT!
WARNING-TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, EXPOSURE TO EXCESSIVE UV
RADIATION, OR INJURY TO PERSONS:
 Turn off/unplug and allow to cool before replacing bulb.
 Bulb gets HOT quickly! Only contact switch/plug when turning on.
 Do not touch hot lens, guard or enclosure.
 Do not stay in light of skin feels warm.
 Do not look directly at lit bulb.
 Keep lamp away from materials that may burn.
 Use only with a 180W or smaller lamp.
 Do not touch the bulb at any time. Use a soft cloth. Oil from skin may damage bulb.
 Do not operate the lamp with a missing a damaged guard, lamp containment barrier or UV light filter!
BULB INSTALLATION/REPLACEMENT
Important: Always unplug the power cord before installing or replacing bulb and before cleaning or other
maintenance.
1. If shield is pre-installed, then loosen spring (loosen screw on both slips) and remove the bent glass shield.
2. Remove bulb from box, DO NOT remove the protective wrapping or touch bulb with bare fingers at any time.
Expose the ends of the bulb and gently place one end then the other into fixture. Be sure that both ends of bulb
are touching metal contacts. NOW REMOVE WRAPPING
3. Place bent tempered glass over the bulb and then attach with set screws provided. Tighten shield well.
4. Repeat above steps when relamping.

Summary

Critical Safety Warnings

General Hazard Alerts

Covers risks of fire, electric shock, UV radiation, and injury from hot lamps and components.

Bulb Handling Precautions

Instructions for safe bulb replacement, including cooling, touching, and material proximity.

Bulb Installation and Replacement

Step-by-Step Bulb Replacement

Detailed procedure for removing and installing bulbs, including shield handling and contact points.

Assembly and Maintenance

Lamp Assembly Procedures

Instructions for connecting poles, shade, base, and plugging in the lamp, including circuit breaker use.

Lamp Maintenance Tips

Guidance on cleaning glass shields and bulbs to prevent cracking and ensure longevity.

Heat Guard Installation

Mesh Cover Installation Guide

Steps for properly fitting and securing the protective mesh cover (heat guard) onto the shade.

Electrical and Component Safety

Polarized Plug Safety

Explanation of the polarized plug feature for reducing electric shock risk and proper outlet insertion.

UV Protective Shield Information

Details on the UV protective glass shield and user caution for its replacement after bulb changes.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

This document provides comprehensive instructions and safety guidelines for the LS-80910 lamp, a portable lighting device designed for indoor use. The lamp features a floor-standing design with multiple pole sections, a shade, and a base, incorporating a circuit breaker for safety.

Function Description

The LS-80910 is a floor lamp primarily used for general illumination. It operates by screwing together various pole sections to form a complete stand, attaching a shade, and inserting a bulb. The lamp is equipped with a circuit breaker that acts as a safety mechanism, preventing operation if the bulb wattage exceeds the specified limit. It also includes a heat guard (mesh cover) and a UV protective glass shield, which are crucial for safety and bulb longevity.

Important Technical Specifications

• Item Number: LS-80910
• Bulb Type: Type-J
• Maximum Bulb Wattage: 180W (or smaller)
• Power Supply: Standard wall outlet with a polarized plug.
• Safety Features:
  • Circuit breaker (F) to prevent operation with bulbs exceeding 180W.
  • Polarized plug to reduce the risk of electric shock.
  • Heat guard (mesh cover) for compliance with UL regulations.
  • UV protective glass shield to provide ultraviolet radiation protection.
• Components:
  • Shade (A)
  • Top Pole (B)
  • Middle Pole (C)
  • Bottom Pole (D)
  • Base (E)
  • Circuit Breaker (F)
  • Bent tempered glass shield
  • Mesh cover (heat guard)
  • Set screws for shield attachment

Usage Features

Assembly:

1. Place all parts on a flat, scratch-resistant surface.
2. Screw Shade (A) onto Top Pole (B).
3. Screw Middle Pole (C) onto Bottom Pole (D), then onto Base (E). Gently feed excessive wire into the upper pole.
4. Screw Top Pole (B) onto Middle Pole (C). Gently feed excessive wire into the upper pole.
5. Insert the plug into a wall outlet.

Bulb Installation/Replacement:

1. Unplug the power cord before starting.
2. If the shield is pre-installed, loosen the spring (and screws on both clips) and remove the bent glass shield.
3. Remove the new bulb from its box. DO NOT remove the protective wrapping or touch the bulb with bare fingers. Expose only the ends of the bulb.
4. Gently place one end, then the other, into the fixture, ensuring both ends touch the metal contacts.
5. NOW REMOVE THE PROTECTIVE WRAPPING from the bulb.
6. Place the bent tempered glass shield over the bulb and secure it with the provided set screws. Tighten the shield well.
7. Repeat these steps when relamping.

Mesh Cover (Heat Guard) Installation:

1. Place the mesh cover over the shade.
2. Position the clip on the mesh cover, aligning the holes.
3. Slide the clip into the edge of the shade and fasten it with the screw.

Operation:

1. Ensure the power supply plug is fully inserted into the wall outlet.
2. Make sure the lamp's switch is in the "off" position.
3. Press the switch on the circuit breaker box (F) to "on."
4. Use the lamp's switches for full range of light.
5. If the circuit breaker (F) needs to be reset, repeat the above procedure to restore full light functionality.

Safety Precautions (VERY IMPORTANT):

• Proper Alignment: Ensure poles are properly aligned before screwing them together to avoid damaging connection threads. Failure to do so may void the warranty.
• Fire/Shock/UV Risk:
  • Turn off/unplug the lamp and allow it to cool before replacing the bulb.
  • The bulb gets HOT quickly; only contact the switch/plug when turning on.
  • Do not touch the hot lens, guard, or enclosure.
  • Do not remain in the light if your skin feels warm.
  • Do not look directly at a lit bulb.
  • Keep the lamp away from flammable materials.
  • Use only a 180W or smaller lamp.
  • Do not touch the bulb with bare hands; use a soft cloth. Oil from skin can damage the bulb.
  • Do not operate the lamp with a missing or damaged guard, lamp containment barrier, or UV light filter.
• Polarized Plug: This lamp has a polarized plug (one blade wider than the other) to reduce electric shock risk. It will fit into a polarized outlet only one way. If it doesn't fit, reverse the plug. If it still doesn't fit, contact a qualified electrician. Never use an extension cord unless the plug can be fully inserted. Do not alter the plug.

Maintenance Features

• Cleaning: Fingerprints can cause the glass shield and/or bulb to crack and reduce lamp life. The shield and bulb can be cleaned with a soft cloth.
• Relamping: Always unplug the power cord before installing or replacing the bulb or performing any other maintenance. Follow the instructions on the relamping label near the bulb for maximum safety and to ensure years of lighting pleasure.
• Circuit Breaker Reset: If the circuit breaker trips, follow the operational steps to reset it and restore full light functionality.
• Parts Shortage: In case of any parts shortage, inform your dealer immediately.
• Documentation: Save these instructions for future reference.

Lite Source LS-80910 Specifications

General

Brand	Lite Source
Model	LS-80910
Category	Home Lighting
Language	English