AGES 3+ YEARS
ADULT SUPERVISION REQUIRED
ADULT BATTERY INSTALLATION REQUIRED
SKU: 649523
A. 1 Helicopter
B. 1 Remote Control
A.
Illustrations are for reference only. Styles may vary from actual contents.
CAUTION: KEEP FINGERS AWAY
FROM SPINNING PROPELLERS
HELICOPTER AND REMOTE CONTROL PARTS
QUICK START
1) Install 6 “AA” (LR6) batteries in the remote control.
2) Charge the helicopter’s battery for 40-50 minutes.
3) Turn on the helicopter.
4) Turn on the remote control to pair with helicopter.
5) Calibrate sensor by holding LANDING and TAKE OFF buttons at the same time until the green light ashes.
6) Use the buttons and turn the remote control left or right to y your helicopter in an open, indoor area.
NOTE: Please read all instructions before use and keep this manual for future reference.
B.
Before beginning, an adult must install fresh alkaline batteries. Here’s how:
1. Using a Phillips screwdriver (not included), remove the screw and battery compartment cover
located on the back of the remote control.
2. Install six (6) fresh 1.5V AA (LR6) alkaline batteries (not included), making sure the (+) and (-)
ends face the proper direction as indicated inside the battery compartment.
3. Replace the compartment cover and tighten the screw.
BATTERY INSTALLATION
CHARGING THE HELICOPTER
FLYING LESSONS
6 x AA Batteries
1.5V AA/LR6
1.5V AA/LR6
1.5V AA/LR6
1.5V AA/LR6
1.5V AA/LR6
1.5V AA/LR6
Take out the charging cable from the
side of the remote control.
1
O
I = ON
O = OFF
2
3
• If the helicopter crashes, switch the remote control and the helicopter to the OFF positions. Carefully check
that no damage was done to the helicopter in the crash before turning the unit on again.
• For best results, use the helicopter away from bright lights to ensure the receiver can detect the remote
control.
• Do not cover the sensor on the helicopter.
• Keep the remote control within 15 feet (5 meters) of the helicopter to avoid loss of reception.
HELPFUL FLYING TIPS
Place the helicopter on a at surface and stand three feet away with the
remote control at an upward position in front of you.
1
3 FEET
EMERGENCY STOP:
If the helicopter crashes, press and hold the
LANDING button, or press the LANDING and
TAKE OFF buttons at the same time to stop the
propellers. Turn the helicopter and remote
control o. Examine the helicopter for any
damage before switching it on and ying again.
Turn the helicopter OFF (O/ ) and insert the cable
into the charging station under the helicopter.
Turn ON (I / ) the remote control. The light on
the remote will ash in red. It will turn green
when it is fully charged. Unplug the charging
cable and replace the cord in the unit.
TM
CONTENTS
POWER INDICATOR
POWER SWITCH
LANDING
CHARGING PLUG
TAKE OFF
PROTECTIVE RINGS
STABILIZER
STABILIZER LINKAGE
ROTOR BLADES
CHARGING
SOCKET
POWER
SWITCH
SKID
SENSOR
O
I /
PAIRING HELICOPTER AND REMOTE CONTROL
Before beginning, the helicopter and remote control will need to be paired. Here’s how:
Turn the helicopter on (I). The lights on
the front will ash.
O
CALIBRATE SENSOR
1
If playing for the rst time or if it hasn’t been played for a long period of time, the sensor will need to be calibrated.
2
After turning on, place the remote control
on a at surface near the helicopter.
Hold down the LANDING and TAKE OFF
buttons until the green light ashes. Release
the buttons and the light will stop ashing.
Turn the remote control on (I / ).
The light on the front will begin to ash.
Once it is paired, it will stop ashing.
O
I /
PRES AND HOLD
1
2
NOTE: If the power indicator on the remote
control is alternating between green and
red, then the battery power is low. Follow
the instructions under “Battery Installation”
to replace the batteries.
To Next Page
Need help?
General
