Loglift 105Z CE User Manual (English)

Questions and Answers:

C
Christian StoneAug 6, 2025
Why are the slewing movements irregular or noisy on my Loglift Construction Equipment?
- J
  Justin PrattAug 7, 2025
  If the slewing movements are irregular or you notice abnormal noises in your Loglift Construction Equipment, first, check the oil level in the hydraulic system and top it up if necessary. Also, ensure the oil in the gearbox is at the required level. While slewing, lubricate the bearing assemblies. If the problem persists, it may indicate damage to the bearing assemblies or pinion, requiring professional attention at a HIAB service workshop.
H
Holly CharlesAug 14, 2025
How to fix a noisy hydraulic pump in Loglift Construction Equipment?
- C
  Charles GreeneAug 14, 2025
  If your Loglift Construction Equipment's hydraulic pump is making noise, it could be due to a blocked oil tank filler cap air filter. Try clearing the blockage or replacing the filler cap. It could also be that the oil level in the tank is too low, so top it up and bleed the hydraulic system. If these steps don't resolve the issue, the pump may be faulty, and you should take it to a HIAB service workshop.
D
Dr. Brendan VillarrealAug 21, 2025
What to do if add-on equipment doesn't work properly on Loglift Construction Equipment?
- T
  Thomas WestAug 21, 2025
  If the add-on equipment isn't working properly on your Loglift Construction Equipment, start by checking the connectors. Ensure they are correctly connected according to the instructions. If the issue continues, there might be another defect, and you should seek assistance from a HIAB service workshop.
S
Scott SummersAug 28, 2025
Why don't the stabilizer extensions slide out on my Loglift Construction Equipment?
- K
  Kimberly WareAug 29, 2025
  If the stabilizer extensions on your Loglift Construction Equipment do not slide out, first check if they are locked and unlock them. If they are unlocked, the issue might be a hydraulic fault, and you should consult a HIAB service workshop.

Loglift 105Z CE Specifications

General

Brand	Loglift
Model	105Z CE
Category	Construction Equipment
Language	English

Summary

1. Introduction

1.1. This Operator's Manual is intended for the operator of this Loglift crane

Defines the scope and content of the operator's manual for the Loglift crane.

1.2. Indications in the Operator's Manual

Explains the various symbols and indications used throughout the operator's manual.

1.3. Identification of this crane

Provides fields to record the crane's mark, type, serial number, and manufacture year.

2. Structure and parts of the crane

2.1. Main groups

Lists the main groups of the crane: crane base, boom system, stabiliser system, operating system.

2.2. Crane base with column and slewing system

Details the components of the crane base, column, and slewing system.

2.3. Boom system and add-on lifting accessories

Describes the boom system components, including extensions and grapple.

2.4. Stabiliser system

Explains the stabiliser system, including beam, extensions, locking device, and legs.

2.5. Operating system - hydraulic components

Lists hydraulic components: oil tank, pump, valves, actuators, hoses, and filters.

2.6. Buttons on the control panel [option]

Details the buttons on the control panel for operating stabiliser and crane systems.

2.7. Premium high seat [option]

Describes the features and adjustment controls for the premium high seat.

2.8. Main control valve

Explains the main control valve and how to operate levers based on symbols.

2.9. Stabiliser control valve

Describes the stabiliser control valve, operated by levers or from the high seat.

3. Safety precautions and warnings

3.1. Operating conditions

Specifies conditions for safe crane use: ventilation and wind speed limits.

3.2. Wind speeds

Table detailing wind forces, speeds, and their characteristics affecting crane use.

3.3. Noise declaration

States the declared dual-number noise emission values for loader cranes.

3.4. Signs on the crane

Illustrates and explains various safety signs found on the crane.

3.5. Maximum load

Explains lifting capacity, load moment, load plate, and safe load limits.

3.6. Signals when using a crane

Details standard hand signals for crane operation and emphasizes following instructions.

3.7. Use of the crane

Covers safe practices for starting, operating, and ending crane use, including stabiliser deployment.

4. The CE system [option]

4.1. How the CE system works

Explains the CE-safety system's role in monitoring and ensuring safe operation.

4.2. Components in the CE System

Identifies and illustrates the main components of the CE system.

4.3. Buttons and indicating lights on the interface

Describes the stop button, supply voltage lamp, and oil pressure lamp on the interface.

5. Manual control system [option]

5.1. Operation from the high seat

Details operating crane controls from the high seat using levers and foot pedals.

6. Starting crane operation

6.1. Starting operations

Covers placing the vehicle and engaging the PTO for crane operation.

6.2. Attach the crane to the vehicle

Provides safety warnings and steps for attaching the crane to the vehicle.

6.3. Electric tiltable seat [option]

Explains how to operate the electric tiltable seat up or down.

6.4. Extend stabiliser extensions and set stabiliser legs

Details extending stabiliser extensions, setting legs, ground conditions, and operating the boom system.

7. During operation

7.1. Operate the crane

Outlines the correct order for lifting loads and general warnings during operation.

7.2. Slope control [option]

Explains the slope indicator and system reaction to exceeding permitted tilt angles.

8. Ending crane operation

8.1. Operate the crane to transport position

Provides step-by-step instructions for retracting the boom for transport.

8.2. Placing the stabiliser system in transport position

Details retracting and securing stabiliser legs and extensions for transport.

8.3. Electric tiltable seat [option]

Explains how to operate the electric tiltable seat up or down.

8.4. Ending use

Covers stopping pump, disengaging PTO, and transport precautions.

8.5. Warning interface (TWI)

Explains TWI system warnings for stabiliser position and boom angle.

8.6. Emergency operation of the dump valve

Provides steps for emergency dump valve operation to park the crane.

9. Maintenance and Service

9.1. Warranty

Outlines warranty fulfillment conditions: inspections, approved parts.

9.2. Service

Provides critical safety warnings regarding welding, drilling, and reinstallation.

9.3. Follow the maintenance instructions!

Emphasizes regular workshop inspections and accessory maintenance, including daily checks.

9.4. Lubrication

Stresses following the lubrication schedule to prevent serious damage.

9.5. Adjust the lateral clearance of the boom and/or hydraulic extension

Explains how to adjust the lateral clearance of the boom and hydraulic extension.

9.6. Adjust the chain in the telescope

Details adjusting chain tension in the telescope for correct operation.

9.7. Hydraulics

Covers checking oil levels, changing oil, bleeding air, and replacing filter cartridges.

9.8. Troubleshooting

Offers solutions for common faults in the crane and its CE device, detailing faults, causes, and actions.

10. Technical Data

10.1. Load plate table

A table for the installer to fill in valid load capacities (meters and kilos).

11. Decommissioning

11.1. Decommissioning a crane

Guidelines for environmentally sound decommissioning and waste sorting of the crane.

Related product manuals

Loglift 96S CE

96 pages

Loglift 105Z CE User Manual

Table of Contents