Lovato ADXL 0085 600 User Manual

Doc: I456GB06_16.docx 29/06/2016 p. 1 / 20
ADXL…
SOFT STARTER
INSTRUCTION MANUAL
 Read the manual carefully before installation and use.
 T
hese devices must be installed by qualified personnel, in compliance with current plant-engineering regulations, in order to avoid damage to persons or property.
 Before any maintenance operation on the device, switch off power supply from measuring and supply inputs.
 The manufacturer assumes no responsibility for electrical safety in the event of improper use of the device.
 The products described in this document are subject to updates or modifications at any time. Data and descriptions in the catalogue therefore do not have any contractual value.
 The building’s electrical system must incorporate a switch or circuit breaker. It must be installed close to the equipment and within easy reach of the operator. It must be marked as the disconnecting
device of the equipment: IEC/ EN 61010-1 § 6.12.2.1.
 Clean the instrument with a soft cloth. Do not use abrasives, liquid detergents or solvents.
Contents Page
Description 2
Front button functions 2
Front LEDs 2
Display indications 2
A
UTOSET guided configuration 3
Navigating the display pages 4
Operational status 4
Remote keypad 4
Startup methods 5
Protections 5
Motor thermal protection 6
Motor thermal protection via PTC 6
Starter thermal protection 6
Main menu 7
Password-protected access 7
Inputs, outputs, internal variables 7
Limit thresholds (LIMx) 7
Remote variables (REMx) 7
User alarms (UAx) 8
IR programming port 9
Parameter setting from PC 9
Parameter setting from smartphone or tablet with CX02 Wi-Fi dongle 9
Parameter setting from smartphone or tablet with NFC 9
Parameter settings (setup) from front panel 10
Parameter table 10
A
larms 13
A
larm properties 13
Table of alarms 14
Description of the alarms 14
Programmable input functions table 14
Programmable input defaults settings 15
Programmable output functions table 15
Programmable output defaults settings 15
Commands menu 16
Installation 16
Recommendations 16
Power factor correction 16
Connection diagrams 17
Mechanical dimensions 18
Terminal layout 18
Choosing the soft starter 19
Type 2 coordination 19
Technical characteristics 19
Manual review history 20
I456GB06_16

Lovato ADXL 0085 600 Specifications

General

Brand	Lovato
Model	ADXL 0085 600
Category	Controller
Language	English

Summary

AUTOSET guided configuration

Startup methods

Protections

Motor thermal protection

Details the electronic motor thermal protection, its display, and trip characteristics.

Motor thermal protection via PTC

Explains the use of a PTC sensor for motor thermal protection.

Starter thermal protection

Describes the starter's internal thermal protection and its status indication.

Main menu

Limit thresholds (LIMx)

Setting parameters (set-up) from the front panel

P04 - PROTECTIONS

P04.01 - Enable motor thermal protections

Enables or disables motor thermal protections for the starter.

P04.02 - Starting thermal protection class

Sets the thermal protection class for motor starting phases.

P04.03 - Run thermal protection class

Sets the thermal protection class for motor running phases.

P05 - MISCELLANEOUS

P05.01 - Torque control

Determines if acceleration/deceleration ramps use torque or voltage control.

P06 - PROGRAMMABLE INPUTS

P07 - PROGRAMMABLE OUTPUTS

Alarms

Explains how alarms are displayed and indicated on the starter.

Alarm properties

Details the various properties that can be assigned to alarms for customized behavior.

Table of alarms

Description of the alarms

Provides detailed explanations for each alarm code, including reasons for tripping.

Commands menu

Installation

Provides essential recommendations and steps for installing the soft starter.

Recommendations

Connection diagrams

Choosing the soft starter

Type 2 coordination

Technical characteristics