Lovato DCRL3 - User Manual

Doc: I377ROGB03_14.doc 04/03/2014 p. 1 / 19
DCRL3 – DCRL5 DCRL3 – DCRL5
Controler automat al Automatic Power Factor
factorului de putere Controller
MANUAL DE UTILIZARE INSTRUCTIONS MANUAL
● Înainte de efectuarea oricărei operaţiuni de întreţinere asupra dispozitivului, îndepărtaţi toate
tensiunile de la intrările de măsurare şi de alimentare şi scurtcircuitaţi bornele de intrare CT.
● Produsele ilustrate în prezentul sunt supuse modificărilor şi schimbărilor fără notificare
anterioară.
● Datele tehnice şi descrierile din documentaţie sunt precise, în măsura cunoştinţelor noastre,
dar nu se acceptă nicio răspundere pentru erorile, omiterile sau evenimentele neprevăzute care
apar ca urmare a acestora.
● Trebuie inclus un disjunctor în instalaţia electrică a clădirii. Acesta trebuie instalat aproape de
echipament şi într-o zonă uşor accesibilă operatorului. Trebuie marcat ca fiind dispozitivul de
deconectare al echipamentului: IEC/EN 61010-1 § 6.11.2.1.
● Curăţaţi instrumentul cu un material textil moale şi uscat; nu utilizaţi substanţe abrazive,
detergenţi lichizi sau solvenţi.
● Before any maintenance operation on the device, remove all the voltages from measuring
and supply inputs and short-circuit the CT input terminals.
● Products illustrated herein are subject to alteration and changes without prior notice.
● Technical data and descriptions in the documentation are accurate, to the best of our
knowledge, but no liabilities for errors, omissions or contingencies arising there from are
accepted.
● A circuit breaker must be included in the electrical installation of the building. It must be
installed close by the equipment and within easy reach of the operator. It must be marked as
the disconnecting device of the equipment: IEC /EN 61010-1 § 6.11.2.1.
● Clean the instrument with a soft dry cloth; do not use abrasives, liquid detergents or
solvents.
Index
Pagina
Introducere
1
Descriere
2
Funcţiile tastaturii
2
Indicaţii afişaj
2
Moduri de operare
3
Măsuri
4
Blocare tastatură
5
Extensibilitate
5
Portul de programare IR
6
Setarea parametrilor prin PC
6
Setarea parametrilor prin tablete sau smartphone-uri
6
Setarea parametrilor (configurare) din panoul frontal
6
Configurare CT rapidă
7
Tabelul parametrilor
8
Alarme
12
Descriere alarme
12
Proprietăţi implicite alarme
13
Meniul comenzilor
14
Utilizarea modulului dongle CX02
14
Instalare
15
Scheme electrice
15
Dispunere borne
17
Dimensiunile mecanice şi decuparea în panoul frontal
17
Caracteristici tehnice
17
Istoric de revizii ale manualului
18
Index
Page
Introduction
1
Description
2
Keyboard functions
2
Display indications
2
Operating modes
3
Measures
4
Keypad lock
5
Expandability
5
IR programming port
6
Parameter setting through PC
6
Parameter setting through tablets or Smarphones
6
Setting of parameters (setup) from front panel
6
Rapid CT setup
7
Parameter table
8
Alarms
12
Alarm description
12
Default alarm properties
13
Command menu
14
CX02 dongle usage
14
Installation
15
Wiring diagrams
15
Terminal arrangement
17
Mechanical dimensions and Panel cutout
17
Technical carachteristics
17
Manual revision history
18
Introducere
Unitatea de control automat al factorului de putere DCRL a fost concepută
pentru a oferi funcţii de ultimă generaţie pentru aplicaţiile de compensare a
factorului de putere. Construită cu componente dedicate şi fiind extrem de
compactă, DCRL combină designul modern al panoului frontal cu
instalarea practică şi cu posibilitatea de extindere din spate, unde un modul
din seria EXP poate fi introdus în slot. Ecranul LCD oferă o interfaţă de
utilizator clară şi intuitivă.
Introduction
The DCRL automatic power factor control unit has been designed to offer
state-of-the-art functions for power factor compensation applications.
Built with dedicated components and extremely compact, the DCRL
combines the modern design of the front panel with practical installation
and the possibility of expansion from the rear, where one EXP series
module can be slotted. The LCD screen provides a clear and intuitive
user interface.
I377 RO GB 0314
AVERTIZARE!
 Citiţi cu atenţie manualul înainte de instalare sau utilizare.
 Acest echipament va fi instalat de personal calificat, în conformitate cu
standardele actuale, pentru a evita deteriorări sau pericolele.
WARNING!
 Carefully read the manual before the installation or use.
 This equipment is to be installed by qualified personnel, complying to
current standards, to avoid damages or safety hazards.
GB
RO

Summary

General Safety Warnings

Product Overview

Front Panel Interface

Keyboard Functions

Explains the function of the MODE, UP, DOWN, and MAN-AUT keys for navigation and selection.

Display Indicators

Details the meaning of various icons and indicators shown on the main and secondary displays.

Operating Modes

TEST Mode Operation

Allows manual activation of individual relay outputs for initial setup and wiring verification.

Manual (MAN) Mode

Explains manual step selection and activation/deactivation of individual steps.

Automatic (AUT) Mode

Details automatic operation for optimal capacitor step configuration.

Measured Parameters

Parameter Navigation

Explains how to cycle through available measurements using the MODE key and automatic rotation.

Keypad Lock Functionality

Expandability Options

Installing Expansion Modules

Step-by-step guide for inserting EXP series modules into the DCRL unit.

Supported EXP Module Types

Lists the types of EXP modules available for system expansion.

Parameter Setting Methods

IR Programming Port

Details using IR-USB (CX01) or IR-WiFi (CX02) dongles for device configuration.

PC Parameter Configuration

Explains using DCRG software to transfer parameters between DCRL and PC.

Front Panel Parameter Setup

Guides users through accessing and modifying parameters via the front panel interface.

Parameter Menu Navigation

Submenu Access and Navigation

Details the codes and descriptions of available submenus for parameter access and navigation.

Rapid CT Configuration

Advanced Parameter Menu

Alarm Configuration Parameters

Alarm System Overview

Alarm Descriptions

Provides detailed descriptions for each alarm code, explaining the fault condition and its cause.

Default Alarm Properties

Commands Menu Operations

Maintenance and Configuration Commands

Lists commands for resetting intervals, counters, backups, and restoring factory defaults.

CX02 Dongle Functionality

CX02 Dongle Commands

Lists the commands available via the CX02 dongle for device setup, cloning, and information retrieval.

Device Installation

Wiring Diagrams

Wiring Configurations

Single-Phase Wiring

Details the wiring configuration for single-phase applications, including voltage and current inputs.

MV (Medium Voltage) Wiring

Illustrates the wiring configuration for medium voltage applications with measurement and correction.

Terminal Layout

Mechanical Dimensions and Panel Cutout

Technical Specifications

Additional Technical Details

Lovato DCRL3 Specifications

General

Brand	Lovato
Model	DCRL3
Category	Controller
Language	English