Lowrance LDT-3003 User Manual

1
LDT-3003
Installation and Operation
Instructions
The LDT-3003 combines a clock, hour meter, voltmeter, and up to three
temperature sensors in one housing. (Since the LDT-3003 is packed
with different options, you may not have all three temp sensors.) It
shows the temperature in either °F or °C, selectable by the user. This
unit fits in a standard 2 1/8" (54 mm) hole used by most marine equip-
ment manufacurers.
Mounting
The LDT-3003 mounts in any dash or flat panel that's at least 2 1/2" (64
mm) in diameter. To mount the unit, first make certain there is at least
3 3/4" (95 mm) from the front of the dash to any obstruction behind the
dash. Also, be sure there is room to route the power and sensor cables.
The maximum usable dash thichness is 1 1/8" (28.5 mm).
1234567
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1
23456
7
1234567
3 3/4" minimum
When you determine the location for the LDT-3003, drill a 2 1/8" (54
mm) hole in the dash. Slide the LDT-3003 through the hole from the
front of the dash. Align it so that it's straight, then tighten the two
screws with a phillips-head screwdriver.
Place the pushbuttons into the holes in the bezel and snap it on to the
LDT-3003. The unit is now ready for wiring.
DASH
TIGHTEN
THESE
SCREWS

Lowrance LDT-3003 Specifications

General

Brand	Lowrance
Model	LDT-3003
Category	Clock
Language	English

Summary

Mounting

Wiring

Sensors

Sensor Types and Combinations

Details available sensor models TS-W2BK and TS-3BK and their usage combinations for temperature displays.

Operation

Clock Display

Shows the current time, with a dot indicating AM/PM, and continues running even when unit is off.

Water Temperature Display

Displays the temperature from the sensor mounted on the transom for water contact.

T2 Temperature Display

Displays the second temperature sensor reading, usable for live well or outside air.

T3 Temperature Display

Displays the third temperature sensor reading, usable for live well or outside air.

Engine Hour Meter

Shows total engine hours operated, sensed from tachometer; requires unit to be on.

Voltmeter Display

Indicates the current electrical system voltage of the boat.

Settings

Set Clock

Procedure to set the current time on the unit, adjusting hours and minutes.

Set Clock Alarm

Instructions for setting an audible alarm based on a specific time.

Set Temperature Alarm

Configuration for setting audible alarms based on temperature thresholds for sensors.

Set Fahrenheit or Celsius

Guide to switch temperature display units between Fahrenheit and Celsius.

UPS Return Service - U.S.A. Only

Accessory Ordering Information

Full One-Year Warranty

How to Obtain Service (Canadian Customers Only)

How to Obtain Service (International Customers Only - Except Canada)

How to Obtain Service - U.S.A. Only