LSDA TS900 Series - User Manual

Electronic Access Control
Electronic Touch Screen Locks, TS900 Series
Copyright © IDN Global, Inc. All rights reserved. • MCEACTS900 0418
www.LSDA.com
Getting Started With Your Electronic Lock
Your new lock is ready for you to program. Here are the basics you need to know. The keypad has digits 0 – 9, plus “C” (clear) and
“#”. You will use # when programming the lock. On the inside, under the battery cover there is a Set Button, used to start a pro-
gramming session.
Your lock comes preset with a Programming Code. It is 1 – 2 – 3 – 4 – 5 - 6- 7 - 8 We encourage you to change this to another 4 to
8 digit code that will not be so obvious. Here’s how you do it:
1. Press and hold the “Set Button” until the lock beeps
2. Enter 1 – 2 – 3 – 4 – 5 – 6 – 7 - 8.
3. Push #.
4. Enter 1 - 0.
5. Press #.
6. Enter your new 4 to 8 digit Programming Code.
7. Press #.
8. Enter your new 4 to 8 digit Programming Code again.
9. Press #. Write down the new Programming Code.
Now it’s time to enter one or more User Codes. These can be 4 to 8 digits long. You will use these to unlock the door from outside.
You can have up to 25 different codes. Here’s how you add a User Code:
1. Press and hold the “Set Button” until the lock beeps.
2. Enter your Programming Code on the keypad.
3. Press # .
4. Enter 2 - 0.
5. Press #.
6. Enter the 4 to 8 digit User Code you want to add.
7. Press #
8. Enter the 4 to 8 digit User Code you want to add again.
9. Press #. Write down the new User Code.
If you have model TS960, adding a User Card is even easier. You can have 25 of these, also.
1. Press and hold the “Set Button” until the lock beeps.
2. Enter your Programming Code on the keypad.
3. Press #.
4. Enter 2 – 3.
5. Press #.
6. Hold the card against the touchscreen. Take it away. Then hold it against the touchscreen again. The card is now valid.
Eventually you will want to disable a User Code. Here’s how you do it:
1. Press and hold the “Set Button” until the lock beeps.
2. Enter your Programming Code on the keypad.
3. Press #.
4. Enter 3 – 0.
5. Press #.
6. Enter 4 to 8 digit User Code you want to delete.
7. Press #.
8. Enter the 4 to 8 digit User Code you want to delete again.
9. Press #.

Summary

Getting Started With Your Electronic Lock

Changing the Default Programming Code

Steps to change the factory default 1-2-3-4-5-6-7-8 programming code for enhanced security.

Adding User Codes

Guide to adding 4 to 8 digit user codes for external door access, with up to 25 codes supported.

Adding User Cards (TS960)

Instructions for enrolling user cards on TS960 models, supporting up to 25 cards.

Disabling User Codes

Procedure to remove or delete previously added user codes from the lock system.

Deleting a User Card (TS960)

Steps to invalidate or remove a previously enrolled user card from the TS960 lock.

LSDA TS900 Series Specifications

General

Type	Smart Door Lock
Material	Zinc Alloy
Battery Life	Up to 12 Months
Fingerprint Capacity	100
PIN Capacity	100
RFID Card Capacity	100
Power Supply	Battery
Unlocking Method	Fingerprint, PIN, RFID Card, Mechanical Key