Lucid Headboard - User Manual

HEADBOARD ASSEMBLY INSTRUCTIONS
PARTS LIST:
(A) M8 bolts x4
(B) Washers x4
(F) Nuts x4
(H) Wall Mount x2
(G) Headboard Mount x2
(I) Screws x16
(J) Drywall Anchor x8
(K) Hex key
(D) M6 Bolts x4
(C) Wrench x1
(E) Washers x4
(A)
(B) (C)
(F)
(D)
(H)
(G)
(E)
(G) Headboard Mount
(G) Headboard Mount
Headboard
Bed Frame
(F) Nuts
(E) Washers
(D) Long Bolts
STEP ONE
Remove the headboard from the box and lay
it face down on the ground. Open the velcro
panel on the back and remove both the legs
and hardware.
STEP TWO
Using two (A) M8 bolts, two (B) washers and
the provided holes, secure both legs to the
headboard at your desired height with the
hex key provided. (see Figure 1)
STEP 3 (recommended)
Using the mounting blocks on the back of your headboard,
screw the two (G) headboard mounts to the top of your
headboard with the provided (I) screws. Using the remaining (I)
screws, attach the (H) wall mounts to your wall. Make sure to
place the wall mounts at the correct height to pair with your
previously installed (G) headboard mounts (see figure 2). If no
wall studs are available to secure the headboard to your wall,
use the provided (J) drywall anchors instead. Lift the headboard
and lower into place to join the (G) and (H) mounts together.
STEP 4
With the front side of the headboard facing the bed frame, attach
the headboard to the frame using the (D) M6 bolts, (E) washers
and (F) nuts.
If your bed frame doesn’t fit the headboard, use the provided modification
plates to secure the bed frame to the headboard. More instructions are
included with the plates.
(A) Medium Bolts
(A) Medium Bolts
(B) Washers
(B) Washers
Legs
Figure 2
Figure 1
Figure 3
Wall
Top of the Headboard
(I) Screws x4
(I) Screws x4
(G) Headboard Mount
(H) Wall Mount
(J) Drywall Anchor x2
(if needed in step 3)
Mounting Block
(I)
(J)
(K)
Failure to follow these warnings and assembly instructions could result
in serious injury or death. Read all instructions before assembling the
headboard. Keep the assembly instructions for future use. Before each
usage or assembly, inspect the headboard for damaged hardware, or
missing parts. DO NOT use the headboard if any parts are missing or
broken. If replacement parts and instructional literature are needed
contact us. DO NOT substitute parts.

Summary

Headboard Assembly Instructions

Step One: Prepare Headboard

Remove the headboard from the box, lay it face down, and open the velcro panel to access legs and hardware.

Step Two: Attach Legs

Secure both legs to the headboard using two M8 bolts and two washers with the provided hex key.

Step Three: Mount Headboard to Wall

Attach headboard mounts to the headboard and wall mounts to the wall, then join them.

Step Four: Attach to Bed Frame

Connect the headboard to the bed frame using M6 bolts, washers, and nuts.

Lifetime Limited Warranty

Warranty Coverage Details

This warranty covers defects in materials or workmanship, with specific exceptions.

Warranty Duration

The warranty coverage lasts for the entire period the original purchaser owns the product.

Exclusions from Coverage

Does not cover wear and tear, misuse, alteration, unauthorized repairs, or transit damage.

Manufacturers Responsibilities

The manufacturer will repair, replace, or refund defective products at their discretion.

How to Obtain Service

Submit warranty claims via email, ensuring you keep your receipt for processing.

State Law Applicability

Details your specific legal rights and how they may vary based on state law.

Lucid Headboard Specifications

General

Brand	Lucid
Model	Headboard
Category	Indoor Furnishing
Language	English